Manual Worx WX623.1 (page 11 of 106) (English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish)

673284

Zoom out

Zoom in

1/106

11 10

Planer EN

11 10

top and tighten it with screw.

7. FITTING A DUST BAG

This accessory can be ﬁtted by sliding the

dust bag inlet over the planer dust extraction

tube(5) as far as possible. The dust bag will

reduce the efﬁciency of the exhaust system

and the bag must be emptied frequently to

maintain the efﬁciency. To empty, open the zip

on the rear of the dust bag.

NOTE: This accessory can be used for

smaller jobs.

8. EXTERNAL DUST EXTRACTION

The dust extraction tube is best connected to a

suitable external dust extraction machine e.g.

vacuum cleaner.

WORKING HINTS FOR YOUR

PLANER

WARNING: Danger of kickback!

Apply the machine to the work

piece only when switched on.

1. STANDARD SURFACE PLANING

Set the desired cutting depth. Position the

front part of the base plate ﬂat onto the work

surface. Switch the machine on and push your

planer forward and it will start cutting, always

maintain all of the base plate ﬂat on the work

surface to prevent the cutting blade jumping.

Move the plane evenly over the work surface.

For most applications 0-3mm max cutting

depth will produce a good surface ﬁnish. It is

best to use small depths of cut and repeat the

planing process.

2. EDGE CHAMFERING

Using the V-groove in the base plate (9) you

can make a chamfer on the work piece edge

(See I). Guide the planer along the edge

and maintain a constant angle and force to

produce a good ﬁnish. You can control the

angle of the chamfer with your hands. Make a

test chamfer on a scrap piece of wood. Ensure

your work piece is clamped and supported

near the edge.

3. REBATING

You use the rebate guide (12) and the parallel

guide (8) accessories (supplied with your tool).

Fit these accessories to your planer. Set the

required rebate depth using the scale and the

mark on the planer housing next to the scale

(See J)Loosen locking screw(7) and adjust

the required rebating width(max 82 mm).

(See K)Tighten locking screw (7). Adjust the

desired rebating depth with the rebate guide

(12) accordingly (max 20mm) (See L).Plane

as often as necessary to achieve the desired

rebating depth. Make sure the plane is guided

with a lateral supporting pressure.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

There are no user serviceable parts in your

power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean

with a dry cloth. Always store your power tool

in a dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard.

ENVIRONMENTAL

PROTECTION

Waste electrical products should not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for

recycling advice.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX623.1 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX623.1 Manual

Product: