Manual Worx WX570 BLADERUNNER (page 13 of 143) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575088

Zoom out

Zoom in

1/143

Multi-function saw EN

2. GUARD ARM ALIGNMENT (See Fig. G)

For your convenience, the guard arm has

already been adjusted to be aligned with

the placement of the blade at the factory.

However, you may also adjust it by following

the instructions below:

(a) Loosen guard arm clamp knob (9).

(b) Loosen adjustment screw (d) under the

arm pivot.

along the support arm until the blade

locates exactly between the guide bearings

without any bending of the blade.

(d) Tighten the locking knob, tighten the

adjustment screw.

OPERATION

WARNING: Always wear safety

goggles or safety glasses with side

shields when operating tools. Failure to do so

could result in objects being thrown into your

eyes causing possible serious injury.

WARNING: Do not use any attachments

or accessories not recommended by

the manufacturer. The use of attachments or

accessories not recommended can result in

serious personal injury.

WARNING: To reduce the risk of injury,

the operator should use the accessory

or attachment according to the instruction.

The tool should be operated at the speed in

accordance with pertinent factors such as:

(a) The dimensions and material of the work

piece;

(b) The size and type of the saw blade.

WARNING: Operating the saw

according to the instruction, never cut

without the guard in place.

WARNING: When lifting or lowering

the guard arm, as indicated in ﬁgure

A2, make sure to avoid putting your ﬁngers

between the gaurd arm and the support arm.

1. ON/OFF SWITCH (See Fig. H)

To turn the machine on, press the on switch (2).

To turn it off, press the off switch (1).

2. VARIABLE SPEED CONTROL

(See Fig. I.1)

The variable speed control is under the work

table. Adjust the variable speed control to

increase or decrease the speed, 6 being the

highest and 1 being the lowest. Speed should

be adjusted according to material thickness

and blade speciﬁcation to be used. Speed

can be adjusted during both load or no load

operation. See Chart 1 for general guidance on

speed selection.”

NOTE: Avoid prolonged use at very low

speed as this may damage your

BladeRunner

’s motor.

Chart 1

Material Speed setting

Wood 5-6

Steel 3-4

Aluminum 4-6

PVC 3-4

Ceramic 3-5

IMPORTANT NOTE: When you cut ceramic,

please use a low feed rate at the end of your

cut. This will help decrease cracking at the end.

We suggest you use a wooden push stick to

complete the cut in ceramic (See Fig. I.2).Push

in the middle of ceramic piece to support it.

Remember to use a vacuum to collect

dust anytime tile is being cut.

GENERAL CUTTING RULES:

(a) ALWAYS allow the blade to reach

operating speed before commencing a

cut.

(b) ALWAYS wait until the blade has

completely stopped before removing

a workpiece or off-cut from close to

the blade.

feed rate which allows the blade to

cut freely without excessive force.

(d) NEVER force a blunt blade to cut with

excessive pressure.

(e) NEVER hold or push the work with

hands in line with the blade.

(f) NEVER operate the BladeRunner

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX570 BLADERUNNER in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX570 BLADERUNNER Manual

Product: