Manual Worx WX570 BLADERUNNER (page 12 of 143) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575088

Zoom out

Zoom in

1/143

Multi-function saw EN

(b) Insert the blade into the blade holder

following the instructions outlined in the

next section of this manual.

rests between the guide rollers (5). (See

Fig. A2)

NOTE: The guard arm has a built in spring

loaded safety mechanism, which causes

it to lower automatically, when the guard

arm clamp knob is not tightened.

(d) Hold the support arm in place and make

sure the blade remains placed in an exact

position between the blade rollers while

tightening the screws. (See Fig. A3)

NOTE: For your convenience, the guard

arm has already been ﬁxed to the

support arm and adjusted to be aligned

with the placement of the blade at the

factory. However, you may also adjust it

if needed (See Adjustment, 2).

2. CHANGE THE BLADE (See Fig. B1, B2,

B3, B4, B5)

Make sure the saw is unplugged. Slacken the

guard arm clamp knob and raise the guard

arm.After raising the guard arm, retighten

the guard arm clamp knob to keep it in place.

(See Fig. B1). Wear gloves to protect your

ﬁngers from the sharp blade. Remove the

desired jigsaw blade from the blade storage

drawer. Attach the blade grip (found in the

small plastic bag) over the tip of the blade

(See Fig. B3). Make sure the grip slides down

the blade as far as it will go. Hold the blade by

the grip. Open the blade holder by depressing

the blade release button, and pull the release

lever ﬁrmly and completely to the right. Hold

the blade release open and insert the blade

into the blade holder using the blade grip.

Push the blade as far into the hole as possible,

making sure the teeth are oriented perfectly

toward the front of the saw. Continue to hold

the blade in place and allow the blade release

lever to slide slowly back to the left. The blade

should now be locked in the proper position. If

not, pull the blade release fully to the right and

try again. The blade will seat properly if the

blade release is pulled fully open, the blade is

pushed ﬁrmly to the bottom of the hole and

held there, and the blade lever is released

smoothly. Remove the blade grip from the

blade by pulling it upward. (See Fig. B5 )

NOTE: The BladeRunner

is designed to use

jigsaw blades 100mm over all length or

less. Do not use jigsaw blades longer than

100mm. Use blades with a t-shank only.

3. STORING THE BladeRunner

ACCESSORIES

(a) MITER GAUGE/RIP FENCE (See Fig.

C1, C2)

Adjust the miter gauge/rip fence to the

position as shown in Fig C2 and tighten the

lock knob. Then press the miter gauge/rip

fence into the miter gauge storage on left

side of the BladeRunner

(b) POWER CORD (See Fig. D1, D2)

For easy storage, the power cord can be

wrapped on the cord wrap (24) on back

side of the BladeRunner

Securing the BladeRunner

to a workbench

or other stable surface during use is

recommended. Use the mounting holes

provided and your own screws or clamps,

or purchase the wall mount, available

separately.

ADJUSTMENT

WARNING: Remove the plug from

the socket before carrying out any

adjustment, servicing or maintenance.

MITER GAUGE POINTER ADJUSTMENT

(See Fig. F)

To check your miter gauge accuracy, use a

combination square (not provided) to make

sure the miter gauge body is 90 degrees to the

shaft.

(a) Loosen the miter gauge angle scale lock

knob (21).

(b) Rotate miter gauge body until it is 90

degrees to the square.

(d) If pointer (b) is not pointing to 90 degrees,

adjust the screw (c), rotate pointer to 0

degrees. Tighten the locking screw (c).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX570 BLADERUNNER in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX570 BLADERUNNER Manual

Product: