575075

Worx WX540 Manual

12
Zoom out
Zoom in
Previous page
1/104
Next page
12V Li-Ion multi-purposed saw EN
1312
with the blade may result in personal injury.
Before you begin work, ensure the material
to be cut is rigid. Small workpieces should be
securely clamped to a work table.
1. SWITCHING ON AND OFF (See Fig. I)
For starting operation of the machine, press
the lock-off button (2) first, then press and
hold the On/Off switch (1) afterwards. To switch
off the machine, release the On/Off switch (1).
For safety reasons the On/Off switch of the
machine cannot be locked; it must remain
pressed during the entire operation.
2. HAND GRIP AREAS
Always ensure you maintain a firm grip while
operating your jigsaw.
3. PROTECTION FINGER
The finger is located in front of the blade
holder. While working, it will help prevent
accidental contact with the moving blade.
4. LED WORK LIGHT
A light (8) is built-in near the end of the
protection finger. The light will automatically
come on each time the on/off switch is
depressed.
5. CUTTING
WARNING: Always wear eye protection
while operating this power tool.
WARNING:
• Never hold the pivot head when operating
the tool.
• Never hold the motor cover when
operating the tool.
Before cutting any type of material, be sure
it is firmly anchored or clamped to prevent
slipping. Holding the work by hand or
against your body leaves it unstable and
may lead to loss of control.
• Place blade lightly against work to be cut,
depress the trigger switch and allow it to
obtain maximum speed before applying
pressure.
• Whenever possible, the saw foot plate
must be held firmly against the material
being cut. This will prevent the saw from
jumping or vibrating and minimize blade
breakage.
• Any cut which puts pressure on the blade,
such as angle or scroll cuts, increases
potential for vibration, kickback and blade
breakage.
WARNING: Shock hazard. Use extra
caution when cutting overhead and pay
particular attention to overhead wires which
may be hidden from view.
WARNING: Use extra caution when
cutting overhead and anticipate the path
of falling branches and debris ahead of time.
WARNING: Inspect work site for hidden
gas pipes, water pipes, or electrical
wires before making blind or plunge cuts.
Failure to do so may result in explosion,
property damage, electric shock, and/or
serious personal injury.
WORKING HINTS FOR YOUR
MULTI-PURPOSED SAW
If your power tool becomes too hot, run no-
load for 2-3 minutes to cool the motor. Avoid
prolonged usage at very low speeds.
GENERAL
Always use a blade suited to the material and
material thickness to be cut.
Always ensure the work–piece is firmly held or
clamped to prevent movement.
Any movement of the material may affect
the quality of the cut. The blade cuts on the
upward stroke and may chip the uppermost
surface.
Ensure your uppermost surface is a non-
visible surface when your work is finished.
MAINTENANCE
Your power tool requires no additional
lubrication or maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX540 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info