575068
21
Zoom out
Zoom in
Previous page
1/136
Next page
Handkreissäge mit Laser D
21
Lesen Sie unbedingt die Anleitung,
damit es nicht zu Verletzungen
kommt
Warnung
Schutzisolation
Schutzbrille tragen
Gehörschutz tragen
Schutzmaske tragen
Laserstrahlung
Nicht in den Strahl sehen
SYMBOLE HINWEISE ZUM BETRIEB
HINWEIS: Lesen Sie das Handbuch vor
Inbetriebnahme des Werkzeuges
sorgfältig durch.
BESTIMMUNGSGEMÄSSER GEBRAUCH:
Das Gerät ist für das Hand-Sägen in Holz,
Holzähnlichen Materialien, Spanplatten
oder kunststoffbeschichtete Spanplatten
vorgesehen. Das Gerät ist für Gerade- sowie
für Schrägschnitte bis 51 ° bei fester Auflage
auf dem Werkstück ausgelegt.
1. SCHNITTTIEFENEINSTELLUNG
(Siehe Abb. A)
Heben Sie den Schnitttiefeneinstellhebel an
und heben Sie das Gehäuse der Säge von der
Grundplatte ab. Stellen Sie die Schnitttiefe
anhand der Skala ein und drücken Sie den
Schnitttiefeneinstellhebel zur Fixierung nach
unten. Addieren Sie grundsätzlich 3 mm zur
Schnitttiefe hinzu, damit das Blatt das gesamte
Material durchschneiden kann.
2. SCHNITTWINKEL EINSTELLEN
(Siehe Abb. B1,B2)
Zum Lösen der Winkelskala drehen Sie den
Grundplatten-Winkelfeststeller (6) gegen
den Uhrzeigersinn. Die Grundplatte von
dem Gerät wegschwenken, bis gewünschter
Schnittwinkel an der Skala(5)eingestellt ist.
Ziehen Sie den Winkelfeststeller (6) durch
Drehen im Uhrzeigersinn an.
VERWENDEN DER
KREISSÄGE
1. SICHERHEITS-EIN-/
AUSSCHALTER(Siehe Abb. C)
Der Schalter ist in der Aus-Position gesperrt,
damit das Werkzeug nicht aus Versehen
anläuft. Drücken Sie den Freigabeknopf,
danach den Ein-/Ausschalter. Anschließend
lassen Sie den Freigabeknopf los. Das
Werkzeug ist nun eingeschaltet. Zum
Ausschalten lassen Sie einfach den Ein-
/Ausschalter los.
Sie können die Entriegelungstaste auf beiden
Seiten der Taste drücken.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX445.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX445.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info