575056

Worx WX426 Manual

11
Zoom out
Zoom in
Previous page
1/142
Next page
Electric Circular Saw EN
11
Large panels tend to sag under their own
weight. Supports must be placed under
the panel on both sides, near the line of cut
and near the edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce narrow kerf causing excessive
friction, blade binding and kickback.
f) Blade depth and bevel adjusting
locking levers must be tight and
secure before making cut. If blade
adjustment shifts while cutting, it may
cause binding and kickback.
g) Use extra caution when making a
“plunge cut” into existing walls or
other blind areas. The protruding blade
may cut objects that can cause kickback.
SAFETY INSTRUCTIONS
FOR PLUNGE TYPE SAW
GUARD FUNCTION
a) Check guard for proper closing before
each use. Do not operate the saw
if guard does not move freely and
enclose the blade instantly. Never
clamp or tie the guard with the blade
exposed. If saw is accidentally dropped,
guard may be bent. Check to make sure
that guard moves freely and does not touch
the blade or any other part, in all angles
and depths of cut.
b) Check the operation and condition of
the guard return spring. If the guard
and the spring are not operating
properly, they must be serviced
before use. Guard may operate sluggishly
due to damaged parts, gummy deposits, or
a build-up of debris.
c) Assure that the base plate of the saw will
not shift while performing the “plunge
cut” when the blade bevel setting is not
at 90°. Blade shifting sideways will cause
binding and likely kick back.
d) Always observe that the guard is
covering the blade before placing
saw down on bench or floor. An
unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is
in its path. Be aware of the time it takes for
the blade to stop after switch is released.
ADDITIONAL SAFETY
RULES FOR YOUR
CIRCULAR SAW
1) Always wear a dust mask, hearing
protection and eye protection.
2) Only use saw blades recommended in the
specification.
3) Do not use any abrasive wheels.
4) Use only blade diameter(s) in accordance
with the markings.
SAFETY INSTRUCTIONS
FOR ABRASIVE
CUTTING-OFF OPERATIONS
CUT-OFF MACHINE SAFETY WARNINGS
a) The guard provided with the tool must
be securely attached to the power
tool and positioned for maximum
safety, so the least amount of wheel
is exposed towards the operator.
Position yourself and bystanders away
from the plane of the rotating wheel.
The guard helps to protect operator from
broken wheel fragments and accidental
contact with wheel.
b) Use only diamond cut-off wheels
for your power tool. Just because an
accessory can be attached to your power
tool, it does not assure safe operation.
C) The rated speed of the accessory
must be at least equal to the
maximum speed marked on the power
tool. Accessories running faster than their
rated speed can break and fly apart.
d) Wheels must be used only for
recommended applications. For
example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side
forces applied to these wheels may cause
them to shatter.
e) Always use undamaged wheel flanges
that are of correct diameter for your
selected wheel. Proper wheel flanges
support the wheel thus reducing the
possibility of wheel breakage.
f) Do not use worn down reinforced
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX426 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX426 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info