Manual Worx WX425 (page 11 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575066

Zoom out

Zoom in

1/128

Circular saw EN

1110

front or back of the motor housing.

WARNING: Disconnect the plug

from the power source before making

any adjustments, changing accessories, or

storing power tools. Such preventative safety

measures reduce the risk of starting the power

tool accidentally.

ATTENTION: When servicing a

tool, ALWAYS use only genuine

replacement parts

1. Locate the plastic motor brush access caps

on either the front or back of the motor

housing.

2. Remove the threaded access cap using a

ﬂat head screwdriver and turn in a counter-

clockwise rotation to loosen. Do not apply

excessive force as this may damage the

access plug.

3. Remove the old motor brush.

4. Insert the new motor brush making sure

that it is completing inserted into the brush

holder.

5. Replace the access cap with the ﬂat-head

screwdriver turning clockwise to tighten.

WORKING HINTS FOR YOUR

CIRCULAR SAW

If your power tool becomes too hot, run it no

load for 2-3 minutes to cool the motor. Avoid

prolonged usage at very low speeds.

Always use a blade suited to the material and

material thickness to be cut. The quality of cut

will improve as the number of blade teeth

increase. Always ensure the work-piece is

ﬁrmly held or clamped to prevent movement.

Support large panels close to the cut line.

Any movement of the material may affect

the quality of the cut. The blade cuts on the

upward stroke and may chip the uppermost

surface or edges of your work piece. When

cutting, ensure your uppermost surface is

a non-visible surface when your work is

ﬁnished. Feeding too fast signiﬁcantly reduces

the performance of the machine and shortens

the life of the saw blade. Always face the

good side of the work piece down to ensure

minimum splintering. Only use sharp saw

blades of the correct type.

For pocket cutting (soft materials only) this

operation requires much skill with a saw and

must only be carried out by a competent

person.

WARNING: The blade teeth are

exposed during this operation, so

operate with extreme caution.

Clearly mark the area to be cut. Set the depth

of cut on the saw. Position the saw over the

marked area with the front edge of the base

plate resting on the work surface and cutting

guide aligned with marked line on workpiece.

Ensure the blade is not touching but is close

to the work surface. The moving lower guard

must be rotated open by using the lever.

Switch on the saw and gently swing the blade

down into the material but maintain a pivoting

force on the front edge of the base. The

moving lower guard can now be released for

normal action of the guard.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no user

serviceable parts in your power tool. Never

use water or chemical cleaners to clean your

power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place.

Keep the motor ventilation slots clean. Keep

all working controls free of dust.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard.

ENVIRONMENTAL

PROTECTION

Waste electrical products should not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for

recycling advice.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX425 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX425 Manual

Product: