575071

Worx WX424 Manual

14
Zoom out
Zoom in
Previous page
1/172
Next page
Mini multi-function saw EN
14
was selected. Always practice in a scrap work
piece to become familiar with this cutting
operation. The selected depth of cut is now
set. When the saw’s blade is manually lowered
(See Fig. Ka, Kb), the blade will be below the
base at the selected depth.
3. ADJUSTING THE 3-POSITION HANDLE
(See Fig. F)
Your saw has handle/motor housing with soft-
grip that adjusts to 3 different cutting angles,
0°, 15°, and 30°. This feature provides more
efficient cutting angles for various applications
and added gripping comfort with maximum
control.
Grasp the handle with one hand and push
the handle adjustment button “IN” to release
the handle for adjustment. Move the handle
forward or backward (See Fig. F) to locate the
3 different positions. When the handle moves
into 1 of the 3 positions the adjustment button
will snap out and the handle will lock into
position. When adjusting the handle, Always
be sure that the button has snapped out and
the handle is locked in position. If the handle
still moves forward or backward, repeat the
process until the handle is locked securely in
position.
WARNING:
Do not operate the
saw if the handle IS not locked in
position and can still move forward or
backward. Failure to lock the handle in 1
of 3 cutting positions could cause loss of
control of saw and result in serious injury.
4. TRIGGER SWITCH (See Fig. G)
To activate the trigger switch to turn the saw
“ON”, place your index and middle fingers
into the molded finger grip trigger safety
release switch, and the other two fingers on
the trigger paddle (See Fig. G). Squeeze the
finger grip “back” until it “clicks”, then depress
the trigger paddle to turn the saw “ON”. To
stop the saw, release your grip on the trigger
paddle, and the finger grip safety release
switch will move back into the “OFF” position.
5. USING THE LASER LIGHT FEATURE
AND LED WORKLIGHT (See Fig. H, I)
WARNING: DO NOT stare into
beam. Only turn laser beam on
when the saw is on the work piece.
Your saw has a built-in laser light. To activate
laser light switch, saw must be plugged into
power source.
a. Do not turn the laser beam on until the saw
is on the work piece.
b. Mark the line of cut on the work piece.
c. Adjust the cutting angle and cutting depth
as needed.
d. Plug in the saw and push the laser switch
forward to turn on the laser.
e. Always shut off the laser light when you
are finished cutting.
f. Your circular saw has a built-in work light
for better visibility when cutting. To turn
on the LED work light, the saw must be
plugged in. Push the switch from OFF to
LED.
6. STARTING A CUT (See Fig. J,K,L1,L2)
a) Set-up and clamp your work piece and
mark your cut line.
b) Set the handle on the saw to the desired
angle for your cutting application.
c) Set the depth of cut (with corresponding
length of cut).
d) Position the front of the saw’s base onto
the leading end (edge) of the work piece
that is solidly supported. Align the center of
the “V” notch on the front of the base with
the cut line (See Fig. J).
e) Manually release the blade guard release
lever while holding the finger lift bracket on
the rear of the base (See Fig. Ka, Kb) as you
lower the saw’s handle and blade to the
selected depth.
Make sure the blade is not making
contact with the workpiece.
f) With both hands on the handle, squeeze
the trigger’s molded finger grip safety
release “backward” while squeezing down
on the paddle switch to turn the saw “On”.
g) Let the blade reach full speed before you
enter the work piece, starting your cut.
h) Press down on the saw, keeping the front
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX424 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX424 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info