Manual Worx WX424 (page 11 of 172) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575071

Zoom out

Zoom in

1/172

Mini multi-function saw EN

KICKBACK IS THE RESULT OF

SAW MISUSE AND/OR INCORRECT

OPERATING PROCEDURES OR

CONDITIONS AND CAN BE AVOIDED

BY TAKING PROPER PRECAUTIONS AS

GIVEN BELOW.

1. Maintain a ﬁrm grip with both hands

on the saw and position your arms to

resist kickback forces. Position your

body to either side of the blade, but

not in line with the blade. Kickback

could cause the saw to jump backwards,

but kickback forces can be controlled by the

operator, if proper precautions are taken.

2. When blade is binding, or when

interrupting a cut for any reason,

release the trigger and hold the

saw motionless in the material until

the blade comes to a complete

stop. Never attempt to remove the

saw from the work or pull the saw

backward while the blade is in motion

or kickback may occur. Investigate and

take corrective actions to eliminate the

cause of blade binding.

3. When restarting a saw in the work-

piece, center the saw blade in the

work piece cut and check that

saw teeth are not engaged into the

material. If saw blade is binding, it may

walk up or kickback from the work-piece as

the saw is restarted.

4. Support large panels to minimize the

risk of blade pinching and kickback.

Large panels tend to sag under their own

weight. Supports must be placed under

the panel on both sides, near the line of cut

and near the edge of the panel.

5. Do not use dull or damaged blades.

Unsharpened or improperly set blades can

cause excessive friction, blade binding and

kickback.

6. Blade depth and bevel adjusting

locking levers must be tight and

secure before making cut. If blade

adjustment shifts while cutting, it may

cause binding and kickback.

7. Use extra caution when making a

“plunge cut” into existing walls or

other blind areas. The protruding blade

may cut objects that can cause kickback.

SAFETY INSTRUCTION FOR MINI MULTI-

FUNCTION SAW WITH LOWER GUARD

1. Check lower guard for proper closing

before each use. Do not operate the

saw if lower guard does not move

freely and close instantly. Never

clamp or tie the lower guard into the

open position. If saw is accidentally

dropped, lower guard may be bent. Raise

the lower guard with the retracting handle

and make sure it moves freely and does

not touch the blade or any other parts, in all

angles and depths of cut.

2. Check the operation of the lower

guard spring. If the guard and the

spring are not operating properly,

they must be serviced before use.

Lower guard may operate sluggishly due

to damaged parts, gummy deposits, or a

build-up of debris.

3. Assure that the guide plate of the saw

will not shift while performing the

“plunge cut” when the blade bevel

setting is not at 90°. Blade shifting

sideways will cause binding and likely kick

back.

4. Always observe that the lower guard

is covering the blade before placing

saw down on bench or ﬂoor. An

unprotected, rotating blade will cause the

saw to walk backwards, cutting whatever

is in its path. Be aware of the time it takes

for blade to stop after ON/OFF switch is

released.

GENERAL SAFETY

WARNINGS FOR YOUR

LASER

WARNING: Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result in

serious injury.

Save all warnings and instructions for

future reference.

These lasers do not normally present an

optical hazard although staring at the

beam may cause ﬂash blindness.

Do not stare directly at the laser beam. A

hazard may exist if you deliberately stare

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX424 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX424 Manual

Product: