Manual Worx WX424.2 (page 13 of 172) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575073

Zoom out

Zoom in

1/172

Mini multi-function saw EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE:

The machine is intended for lengthways

and crossways cutting of wood with straight

cutting lines, alumunium, PVC pipe and tile,

etc., while resting ﬁrmly on the work piece.

1. INSTALL/CHANGE THE BLADE

(See Fig. A)

WARNING: Be sure to wear

protective work gloves while

handling a saw blade. The blade can

injure unprotected hands.

WARNING: This tool will be

extremely hot after use. Be sure

to let saw, blade and blade spindle

clamping screw cool before changing

blades.

a. Unplug the saw.

WARNING: To prevent personal

injury, Always disconnect the plug

from power source before assembling

parts, making adjustments or changing

blades.

b. Loosen the blade spindle clamping screw

using the two hex keys included. Place

one key into the blade spindle clamping

screw and the other key into the back of the

spindle assembly. (See Fig. A)

c. Turn the key that is in the clamping screw

clockwise while holding the other key

stationary.

d. Remove the screw and the blade clamping

washer. (See Fig. B)

e. Set the depth of cut scale to the maximum

depth of 22mm. Release the blade release

lever and rasie the base with the ﬁnger

lift bracket to expose the blade below the

base.

f. Grasp the blade with your gloved hand

and remove the blade, or install the blade,

through the blade slot in the base.

g. Place the new saw blade through the blade

slot in the base and onto the spindle shaft.

NOTE: The teeth of the blade should

point upward at the front of the saw as

shown in (See Fig. B).

NOTE: The warning copy and the Blade

Rotation Arrow shown on the blade should

face outward towards the operator so it can

be viewed (See Fig. C).

h. Replace the blade clamping washer .

i. Replace the spindle screw and hand tighten

it in a counterclockwise direction.

j. Use the two hex keys to tighten the spindle

clamping screw thoroughly.

k. Place the two hex keys back in the case.

NOTE: Never use a blade that is too thick to

allow the blade clamping washer to engage

with the ﬂat side of the spindle.

2. MAKING DEPTH OF CUT

ADJUSTMENTS (See Fig. D)

NOTE: Always use the correct blade depth

setting. The correct blade depth setting for all

cuts should not be more than 6 mm below the

material being cut. Allowing more depth will

increase the chance of kickback and cause the

cut to be rough. Your saw is equipped with

a depth of cut scale that provides increased

depth of cut accuracy. The depth of cut scale

is located on the top of the upper blade guard

(See Fig. D).

Our suggest cut depth:

Max. cut depth

Wood 0-22mm

Alu 0-3mm

PVC pipe 0-12mm

Tile 0-8mm

TO SET THE BLADE DEPTH (Fig. E1, E2)

Determine the desired depth of cut. Unlock

the depth of cut and length of cut Indicator

adjustment/Lock lever. Slide the depth of cut

indicator to the desired depth of cut. Lock

down the depth of cut adjustment / lock lever.

The length of cut indicator (See Fig.D) is ideal

for plunge or pocket cutting into the middle

(or interior) of the work piece when you need

to know where the cut will begin and where

it will end. This feature allows you to pinpoint

the location where the blade will plunge into

the work piece, based on the blade depth that

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX424.2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX424.2 Manual

Product: