Manual Worx WX424.1 (page 15 of 172) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575072

Zoom out

Zoom in

1/172

Mini multi-function saw EN

of the base ﬂat against the work piece as

you slowly push the saw’s blade into the

work piece (See Fig. Kc).

i) Carefully guide the saw through the line

of cut. Do not bind the blade in the cut;

push the saw blade forward at a rate where

the blade is not laboring. When the cut is

complete, release the trigger safety release

and paddle switch and let the blade come

to a complete stop. Do not remove the saw

and blade from the work piece while the

blade is moving. This could damage your

cut, cause kickback, loss of control and

result in serious injury.

j) When the blade and saw are clear of and

removed from the work piece (See Fig. Kf),

the lower blade guard and base will be able

to automatically drop down and the blade

guard release lever will engage the upper

blade guard, locking the blade above the

base (See Fig. Kg).

WARNING: Never use the saw with

your hands positioned as shown in

Fig. L2.

7. MAKING CROSS CUTS AND RIP CUTS

(See Fig. M1, M2)

a) ALWAYS use your saw with your hands

positioned correctly (See Fig. M1, M2).

WARNING: Always maintain

proper control of the saw to make

sawing safer and easier. Loss of control

of the saw could cause an accident

resulting in possible serious injury.

b) When making cross or rip cuts, align your

line of cut with the center of the “V” notch

located on the front of the saw’s base (See

Fig. J).

c) Since the thickness of blades varies,

make a trial cut in scrap material along

the guideline to determine how much, if

any, you should offset the blade from the

guideline to allow for the blade thickness to

get an accurate cut.

Making rip cuts (See Fig. M2)

Always use a guide when making long or

wide rip cuts with your saw. You can use either

a straight edge (sold separately), or use the

parallel guide that is included with your saw.

8. CUTTING WITH A STRAIGHT EDGE

(See Fig. M1)

You can make an efﬁcient rip guide by

clamping a straight edge to your work piece.

a) Mark the position of the side edge of the

saw’s base (cutting platform) and then

securely clamp the straight edge (sold

separately) on the mark and parallel to the

cut line.

b) As you cut, keep the edge of the saw’s base

ﬂush against the straight edge and ﬂat on

the work piece.

c) Always let the blade reach full speed, then

carefully guide the saw into the work piece.

Do not bind the blade in the cut. Push the

saw forward at a speed where the blade is

not laboring.

9. INSTALLING AND USING THE

PARALLEL GUIDE (See Fig. N1,N2,N3)

Your saw comes with a parallel guide that is

7-inches long on the guide edge. It allows you

to make accurate parallel cuts when trimming

a work piece. It attaches to the saw’s base. The

arm of the parallel guide is stamped, on both

sides, 0 to 7 inches in 1/4-inch increments and

1 to 18 centimeters in 10-mm increments for

easy adjustment of your cut. The parallel guide

can be used with the guide edge turned down

to guide along the edge of a work piece for

rip or cross cuts (See Fig. N2), or turned up to

guide against a wall for inside cuts (See Fig.

N3).

a) Position the parallel guide so the arm can

slide into the mounting slots at the front

of the saw’s base (See Fig. N1), and loosen

the retaining screw.

b) Adjust the parallel guide to the desired

length of cut.

c) Tighten the parallel guide locking

screw(20).

d) Clamp and support the work piece securely

before making your cut.

e) Place the parallel guide ﬁrmly against the

edge of the work piece (See Fig.N2), or

against a wall (See Fig.N3). Doing this will

help give you a true cut without pinching

the blade.

f) Be sure that the guiding edge of the work

piece, or the wall, is straight so you can

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX424.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX424.1 Manual

Product: