Manual Worx WX423 (page 10 of 64) (English)

673177

Zoom out

Zoom in

1/64

Electric Circular Saw EN

SAFETY INSTRUCTIONS

FOR ALL SAWS

a) DANGER: Keep hands away from

cutting area and the blade. If both

hands are holding the saw, they cannot be

cut by the blade.

b) Do not reach underneath the

workpiece. The guard cannot protect you

from the blade below the workpiece.

c) Adjust the cutting depth to the

thickness of the workpiece. Less than

a full tooth of the blade teeth should be

visible below the workpiece.

d) Never hold piece being cut in your

hands or across your leg. Secure

the workpiece to a stable platform. It is

important to support the work properly to

minimize body exposure, blade binding, or

loss of control.

e) Hold the power tool by insulated

gripping surfaces only, when

performing an operation where the

cutting tool may contact hidden

wiring or its own cord. Contact with a

“live” wire will also make exposed metal

parts of the power tool “live” and could

give the operator an electric shock.

f) When ripping always use a rip fence

or straight edge guide. This improves

the accuracy of cut and reduces the chance

of blade binding.

g) Always use blades with correct size

and shape (diamond versus round) of

arbour holes. Blades that do not match

the mounting hardware of the saw will run

eccentrically, causing loss of control.

h) Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw,

for optimum performance and safety of

operation.

FURTHER SAFETY

INSTRUCTIONS FOR ALL

SAWS

Kickback causes and related warnings

- Kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the

workpiece toward the operator.

- When the blade is pinched or bound tightly

by the kerf closing down, the blade stalls

and the motor reaction drives the unit

rapidly back toward the operator.

- If the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the

wood causing the blade to climb out of the

kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or

incorrect operating procedures or conditions

and can be avoided by taking proper

precautions as given below.

a) Maintain a ﬁrm grip on the saw and

position your arm to resist kickback

forces. Position your body to either

side of the blade, but not in line with

the blade. Kickback could cause the saw

to jump backwards, but kickback forces

can be controlled by the operator, if proper

precautions are taken.

b) When blade is binding, or when

interrupting a cut for any reason,

release the trigger and hold the

saw motionless in the material until

the blade comes to a complete

stop. Never attempt to remove the

saw from the work or pull the saw

backward while the blade is in motion

or kickback may occur. Investigate and

take corrective actions to eliminate the

cause of blade binding.

c) When restarting a saw in the

workpiece, center the saw blade in

the kerf and check that saw teeth are

not engaged into the material. If saw

blade is binding, it may walk up or kickback

from the workpiece as the saw is restarted.

d) Support large panels to minimize the

risk of blade pinching and kickback.

Large panels tend to sag under their own

weight. Supports must be placed under

the panel on both sides, near the line of cut

and near the edge of the panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX423 in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX423 Manual

Product: