673223

Worx WX390.1 Manual

11
Zoom out
Zoom in
Previous page
1/40
Next page
Cordless Rotary Hammer EN
11
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for hammer drilling
in concrete, brick and stone. It is also suitable
for drilling without impact in wood, metal,
ceramic and plastic. Machines with electronic
control and right/left rotation are also suitable
for screwdriving.
OPERATION
ACTION FIGURE
Removing
The Battery
See Fig. A1
Inserting The Battery See Fig. A2
Selecting The Operating Mode See Fig. B
HAMMER DRILLING
Inserting Drill Bits See Fig. C1
Removing Drill Bits See Fig. C2
DRILLING &
SCREWDRIVING
Inserting Adaptors See Fig. D1
Inserting Bits into Chuck See Fig. D2
Removing Adaptors See Fig. D3
Removing Bits from Chuck See Fig. D4
On/Off Switch See Fig. E
Switch Lock
NOTE: The Switch Trigger
Can Be Locked In The Off
Position.
See Fig. F
Forward Rotation Control See Fig. G
Reverse Rotation Control See Fig. H
LED Light See Fig. I
Temperature Dependent
Overload Protection
/
Protection Against Deep
Discharging
/
WORKING HINTS FOR YOUR
TOOL
If your power tool becomes over heated, set
the speed to maximum and run no load for 2-3
minutes to cool the motor. SDS-plus tungsten
carbide drill bits should always be used for
concrete and masonry.
When drilling in metal, only use HSS drill bits
in good condition. Where possible use a pilot
hole before drilling a large diameter hole.
PROBLEM SOLUTION
1. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, having not used a
battery pack for a prolonged time will reduce
the battery pack working time. This can be
corrected after several charge and discharge
operations by charging & working with your
tool. Heavy working conditions such as large
screws into hard wood will use up the battery
pack energy faster than lighter working
conditions. Do not re-charge your battery pack
below 0
o
C and above 30
o
C as this will affect
performance.
MAINTENANCE
Remove the battery pack from the tool
before carrying out any adjustment,
servicing or maintenance.
Your power tool requires no additional
lubrication or maintenance, except for the
cleaning & lubrication of the SDS bits and
adaptors before inserting into the chuck.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX390.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX390.1 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info