Manual Worx WX382.1 (page 11 of 96) (English, German, Dutch, French, Italian, Polish, Spanish)

575148

Zoom out

Zoom in

1/96

Cordless rotary hammer EN

1110

— REMOVING (See Fig. B3)

Retract back the bit holder locking sleeve (2)

and pull out the bit.

WARNING: Your new WORX Rotary

Hammer Drill generates powerful

forces to get your job done quickly and

effectively. These forces may cause

inferior quality SDS bits to break and jam

in the chuck, We therefore recommend

that only high quality SDS bits be used

with this tool.

2. INSERTING A TOOL INTO CHUCK (13)

(See Fig. C)

To open the chuck jaws rotate the front section

of the chuck while holding the rear section.

Insert the drill bit between the chuck jaws

and rotate the front section in the opposite

direction while holding the rear section.

Ensure that the drill bit is in the center of

the chuck jaws. Finally, ﬁrmly rotate the two

separate chuck sections in opposite directions.

Your drill bit is now locked in the chuck.

3. ON/OFF SWITCH (See Fig. D)

Depress the On/Off switch (4) to start and

release it to stop your tool.

— ON/OFF SWITCH WITH VARIABLE

SPEED CONTROL

Depress the On/Off switch to start and release

it to stop your tool. This tool has a variable

speed switch (4) that delivers higher speeds

with increased trigger pressure - speed is

controlled by varying the pressure applied to

the switch.

4. SWITCH LOCK (See Fig. D)

The switch trigger can be locked in the OFF

position. This helps to reduce the possibility of

accidental starting when not in use. To lock the

switch trigger, place the direction of rotation

control in the center position.

5. FORWARD AND REVERSE ROTATION

CONTROL (See Fig. D)

With the hammer pointing away from you, push

the forward/reverse-lever “

“ to the left for

forward rotation. Push the forward/reverse-lever “

“ to the right for reverse rotation.

WARNING: Never change the

direction of rotation while the tool

is rotating, wait until it has stopped.

6. FUNCTION MODE SELECTION

(See Fig. E)

The operation of the gearbox for each

application is set with the function mode

selection switch (8). To change between

functions, depress the unlocking button

(15) and rotate the selector to the desired

operating mode.

For simultaneous

drilling and impacting

of concrete or masonry,

choose the Hammer

drilling position.

For screw driving,

drilling into steel, wood

and plastics choose the

Rotary drilling position.

WARNING: The operating mode

selector switch may be actuated

only at a standstill.

7. LED LIGHT (See Fig. F)

To turn on the light simply press the on/off

switch. When you release the on/off switch,

the light will be off.

LED lighting increases visibility-great for

dark or enclosed area. LED is also a battery

capacity indicator. It will ﬂash when power

gets low.

8. TEMPERATURE DEPENDENT

OVERLOAD PROTECTION

When using as intended for, the power tool

cannot be subject to overload. When the

load is too high or the allowable battery

temperature of 75°C is exceeded, the

electronic control switches off the power

tool until the temperature is in the optimum

temperature range again.

9. PROTECTION AGAINST DEEP

DISCHARGING

The Li-Ion battery is protected against deep

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX382.1 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX382.1 Manual

Product: