673164
13
Zoom out
Zoom in
Previous page
1/96
Next page
13
Lithium-Ion Brushless drill driver
Lithium-Ion Brushless hammer drill
EN
OPERATING THE ON/OFF SWITCH
WARNING: Do not operate for long periods at low speed
because excess heat will be produced internally.
See Fig. G
LED LIGHT INDICATOR (See Fig. G)
Before operation, the LED light will be activated when the On/Off switch is slightly depressed, and
will automatically turn off 20 seconds after the On/Off switch is released.
The tool and battery are equipped with a protection system. When the LED Light is quickly flashing
3 seconds and turn off, the system will automatically cut off power to the tool to extend battery life.
The tool will automatically stop during operation if the tool and/or battery are placed under one of
the following conditions:
• Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In
this situation, release the Trigger Switch on the tool and stop the application that caused the tool to
become overloaded. Then pull the Trigger Switch again to restart.
• Overheated: Under the condition above, if the tool does not start, the Tool and Battery are
overheated. In this situation, let the Tool and Battery cool before pulling the Trigger Switch again.
• Low battery voltage: The remaining Battery capacity is too low and the tool will not operate. In this
situation, remove and recharge the Battery.
WARNING: To turn on the light, press the On/Off switch and make sure the Forward/
Reverse Rotation Control is on right/left position.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON
WHEN YOU PRESS THE SWITCH?
The Forward and Reverse Switch, which is
on top of the trigger, is positioned in the lock
function. Unlock the Forward and Reverse
Switch putting it into the required rotation
position. Push the trigger and the drill will
start to rotate (See Fig. B).
2. THE DRILL STOPS BEFORE THE
SCREW IS COMPLETELY TIGHTENED.
WHY?
Verify the torque position of the Torque
Adjustment Ring, you can find the Torque
Adjustment Ring between the Chuck and the
drill body. Position 1 is the lowest torque
(screw driving force) and position 22 is the
highest torque (screw driving force). Position
is for drill operation. Position is for
hammer drill operation. Regulate the Torque
Adjustment Ring to a higher position to reach
the best result (See Fig. E).
3. I CAN NOT FIT THE BATTERY INTO
THE BATTERY CHARGER. WHY?
The battery can be inserted into the charger
only in one direction. Turn the battery around
until it can be inserted into the slot, the red
LED Light should turn on when the battery is
charging.
4. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, as above, and
having not used a Battery Pack for a
prolonged time will reduce the Battery Pack
working time. This can be corrected after
several charge and discharge operations by
charging & working with your drill. Heavy
working conditions such as large screws
into hard wood will use up the Battery Pack
energy faster than lighter working conditions.
Do not re-charge your Battery Pack below
0
o
C and above 30
o
C as this will affect
performance.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX373 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX373 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info