673270
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
Nickel-Cadmium
Impact drill
WX369.3 WX369.4
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The machine is intended for the screwing in and loosening of
screws as well as for drilling in wood, metal and plastic.
BEFORE PUTTING INTO OPERATION
- BATTERY CHARGING
A battery that is new or has not been used for a longer period
does not develop its full capacity until after several chargin /
discharging cycles.
A significantly reduced working period after charging indicates
that the batteries are used and must be replaced.
- TO REMOVE OR INSTALL BATTERY PACK
(See Fig. A)
Locate buttons on side of battery pack and depress both sides
to release battery pack from your tool. Remove battery pack
from your tool. After recharge insert the battery pack into
the battery port. A simple push and slight pressure will be
sufficient.
1. AUXILIARY HANDLE
Slide the handle onto the drill and rotate to the desired working
position. To clamp the auxiliary handle, rotates the handgrip
clockwise. To loosen it, rotate the handgrip anti-clockwise.
Always use the handle during operation.
2. ON/OFF SWITCH (See Fig. B)
Depress the On/Off switch to start and release it to stop your
drill. The on/off switch is fitted with a brake function which stops
your chuck immediately when you quickly release the switch.
It is also a variable speed switch that delivers higher speed and
torque with increased trigger pressure. Speed is controlled by
the amount of switch trigger depression.
WARNING: Do not operate for long periods at
low speed because excess heat will be produced
internally.
3. SWITCH LOCK (See Fig. B)
The switch trigger can be locked in the OFF position. This helps
to reduce the possibility of accidental starting when not in use.
To lock the switch trigger, place the direction of rotation selector
in the center position.
4. REVERSIBLE (See Fig. B)
For drilling and screw driving use forward rotation marked
” (lever is moved to the left). Only use reverse rotation
marked “
” (lever is moved to the right) to remove screws
or release a jammed drill bit.
WARNING: Never change the direction of rotation
when the chuck is rotating, wait until it has
stopped!
5. TWO-SPEED GEAR CONTROL (See Fig. C)
The drill has a two-speed gear control designed for drilling
or driving at LO (mark is 1) or HI (mark is 2) speeds. A slide
switch is located on top of the drill to select either LO or HI
speed. When using the drill in the LO speed range, the speed
will decrease and the drill will have greater power and torque.
B
C
D1
D2
A
F
E
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX369.3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX369.3 in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info