575042

Worx WX368 Manual

11
Zoom out
Zoom in
Previous page
1/124
Next page
Lithium-Ion cordless hammer drill EN
11
3. SWITCH LOCK (See Fig.B)
The switch trigger can be locked in the OFF
position. This helps to reduce the possibility of
accidental starting when not in use. To lock the
switch trigger, place the direction of rotation
selector in the center position.
4. REVERSIBLE (See Fig.B)
For drilling and screw driving use forward
rotation marked “ ” (lever is moved to the
left). Only use reverse rotation marked
“ ” (lever is moved to the right) to remove
screws or release a jammed drill bit.
WARNING: Never change the
direction of rotation when the
chuck is rotating, wait until it has
stopped!
5. TWO-SPEED GEAR CONTROL (See
Fig.C)
The drill has a two-speed gear control (11)
designed for drilling or driving at LO (mark is
1) or HI (mark is 2) speeds. A slide switch is
located on top of the drill to select either LO
or HI speed. When using the drill in the LO
speed range, the speed will decrease and the
drill will have greater power and torque. When
using the drill in the HI speed range, the speed
will increase and the drill will have less power
and torque.
Gear I
Low speed range: for screwdriving or working
with large drilling diameter.
Gear II
High speed range: for working with small
drilling diameter.
WARNING: To prevent gear damage,
always allow the chuck to come
to a complete stop before changing the
direction of rotation or the two-speed
gear train.
6. CHUCK ADJUSTMENT (See Fig.D)
To open the chuck jaws rotate the front section
of the chuck (1). Insert the drill bit between the
chuck jaws and rotate the front section in the
opposite direction. Ensure the drill bit is in the
center of the chuck jaws. Finally, firmly rotate the
front chuck section in the opposite directions.
Your drill bit is now clamped in the
chuck.
7. TORQUE ADJUSTMENT AND HAMMER
OR DRILLING CONTROL (See Fig.E)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring (2). The torque is greater
when the torque adjustment ring is set on
a higher setting. The torque is less when
the torque adjustment ring is set on a lower
setting.
When drilling in masonry and concrete choose
the hammer position .
When drilling in wood, metal, plastic and
screwdriver choose the drill position .
Make the setting as follows:
1 - 4 for driving small screws
5 - 9
for driving screws into soft
material
10 – 14
for driving screws into soft and
hard material
15 - 19 for driving screws into hard wood
20 for driving larger screws
for heavy drilling
for drilling in masonry and
concrete
8. AUTOMATIC SPINDLE LOCK (See Fig.F)
The automatic spindle lock allows you to
use as a regular screwdriver. You can give an
extra twist to firmly tighten a screw, loosen
a very tight screw or continue working
when the battery energy has expired. For
manual screwdriver purposes, the chuck is
automatically locked when the tool is off.
9. SIGHT LIGHT
The sight (3) light allows you to keep a clear
view under less illuminated circumstances.
To turn on the light simply press the on/off
switch. When you release the on/off switch,
the light will go out.
10. LEVEL DRILLING (See Fig.G)
The Bubble level (10) is recessed in the motor
housing on the top of the drill. It can be used
to keep the drill level during horizontal drilling
operation.
The Bubble level (10) is recessed in the motor
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX368 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX368 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info