Manual Worx WX330 (page 9 of 80) (English, German, Dutch, French, Italian, Polish, Spanish)

575144

Zoom out

Zoom in

1/80

Rotary hammer EN

OPERATING

INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for hammer drilling

in concrete, brick and stone as well as for light

chiseling work. It is also suitable for drilling

without impact in wood, metal, ceramic and

plastic.

1. CHANGING THE DRILL CHUCK

(See Fig. A) (WX330)

• Removing the replacement drill chuck

WARNING: Before removing the

replacement drill chuck, always

remove the tool or bit!

With the drill pointing toward you, grasp the

locking ring (7) of the SDS-plus “quik-change”

chuck and pull forward ﬁrmly, then rotate it to

the side. The SDS-plus “quik-change” chuck

will come free.

• Attaching the replacement drill chuck

When mounting the precision keyed chuck,

grasp the precision keyed chuck with the

whole hand, pull it back as far as it will go,

then rotate it to the side until it can clearly

be heard to latch. The precision keyed chuck

locks itself. Check locking by pulling on the

precision keyed chuck. Make replacements in

a corresponding manner.

2. INSERTING AND REMOVING DRILL

BIT IN SDS

Take care that the dust protection cap

(9) is not damaged when changing tools.

• INSERTING

Clean and lightly oil the bit before inserting.

Insert the dust-free bit into the bit holder with

a twisting motion until it latches.

The bit locks itself. Check the locking by

pulling on the tool.

• REMOVING

Retract back the bit holder locking sleeve (8)

and pull out the bit.

WARNING! Your new WORX Rotary

Hammer Drill generates powerful forces

to get your job done quickly and effectively.

These forces may cause inferior quality

SDS bits to break and jam in the chuck, We

therefore recommend that only high quality

SDS bits be used with this tool.

3. MOUNTING OF BIT IN KEYED CHUCK

(WX330 WX330.2)

WARNING: Do not use tools without

SDS-plus for hammer drilling or

chiseling!

Before mounting the drill bit, attaching the 13

mm keyed chuck, insert bit between the chuck

jaws as far as it will go. Ensure drill bit is in

the center of the chuck jaws. Using the chuck

key provided, there are three holes in which

the chuck key should be inserted. Tighten them

equally in turn at each of the three holes, not

just at one hole. Your drill bit is now locked

in the chuck. The bit can be removed by

reversing the above procedure (See Fig. B).

4. INSERTING/REMOVING THE DRILL

CHUCK (See Fig. C)

• Inserting the drill chuck

To work with tools without SDS-plus (e.g.,

drills with cylindrical shafts), a suitable drill

chuck must be used. Insert the adapter (14) of

the drill chuck (13) with a twisting motion into

the SDS-plus chuck (12) until it can be heard to

lock. The adapter locks itself. Check the locking

by pulling on the drill chuck.

• Removing the drill chuck

To remove the drill chuck (13), pull the locking

sleeve (8) to the rear, hold in this position and

remove the drill chuck from the tool holder.

5. ON/OFF SWITCH WITH VARIABLE

SPEED CONTROL

Depress to start and release to stop your tool.

This tool has a variable speed switch (1) that

delivers higher speeds with increased trigger

pressure - speed is controlled by varying the

pressure applied to the switch. (See Fig. D)

6. SWITCH LOCK-ON BUTTON

Depress the on/off switch (1) then the lock

on button (2) (See Fig. D); release the on/off

switch ﬁrst and the lock-on button second.

Your switch is now locked on for continuous

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX330 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX330 Manual

Product: