Manual Worx WX311 (page 9 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575021

Zoom out

Zoom in

1/104

Impact drill EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for impact drilling

in brick, concrete and stone as well as for

drilling in wood, metal and plastic.

1. AUXILIARY HANDLE (See Fig. A)

Slide the handle onto the drill and rotate

to the desired working position. To clamp

the auxiliary handle rotates the handgrip

clockwise. To loosen the auxiliary handles

rotate the hand grip anti-clockwise. Always

use the auxiliary handle.

WARNING! Always check and

rotate the handle tightly before

using to avoid any accident.

2. INSTALLING THE DEPTH GAUGE (See

Fig. B)

The depth gauge can be used to set a

constant depth to drill. To use the depth

gauge, loosen the handle by rotating the

bottom section of handle anti-clockwise.

Insert the depth gauge through hole in

handle. Slide the depth gauge to required

depth and tighten fully.

3. INSERTING A TOOL INTO CHUCK

(See Fig. C.1&C.2)

KEY CHUCK (9) (WX311)

Remove chuck key from key storage tab

at base of drill handle, then place key into

chuck, turn key anti-clockwise to undo/

loosen chuck, inset drill/tool and ﬁrmly

tighten chuck by turning key clockwise.

Remove key and replace in storage tab at

base of drill handle (See Fig C.1).

KEYLESS CHUCK (1) (WX311.1)

To open the chuck jaws rotate the front

section of the chuck while holding the rear

section. Insert the drill bit between the

chuck jaws and rotate the front section in

the opposite direction while holding the

rear section. Ensure that the drill bit is in the

center of the chuck jaws. Finally, ﬁrmly rotate

the two separate chuck sections in opposite

directions. Your drill bit is now locked in the

chuck. (See Fig C.2)

4. ON/OFF SWITCH

Depress to start and release to stop your

tool.

It is also a variable speed switch that delivers

higher speed and torque with increased

trigger pressure. Speed is controlled by the

amount of switch trigger depression.

5. SWITCH LOCK-ON BUTTON (See Fig.

Depress on/off switch (7) then lock-on button

(5), release on/off switch ﬁrst and lock-on

button second. Your switch is now locked on

for continuous use. To switch off your tool

just depress and release the on/off switch.

6. FORWARD AND REVERSE ROTATION

CONTROL (See Fig. E)

For drilling and screw driving use forward

rotation marked “



” (lever is moved to

the left). Only use reverse rotation marked

“



” (lever is moved to the right) to remove

screws or release a jammed drill bit.

WARNING! Never change the direction

of rotation when the tool is rotating,

wait until it has stopped.

7. HAMMER OR DRILLING CONTROL

(See Fig. F)

When drilling masonry and concrete choose

the Hammer position “

“When drilling

wood, metal, plastic and screw driving

choose the Drill position”

“.

8. GEAR BOX SWITCH

Choose position I (See Fig. G)for high

torque/low speed range for large diameter

drill bits and screw driving. Choose position

II (See Fig. H)

for low torque/ High-speed range for small

diameter drill bits. If the gears do not engage

easily then rotate the chuck by hand to align

the gears. Never change the gears when the

tool is rotating, wait until it has stopped.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX311 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX311 Manual

Product: