673206
11
Zoom out
Zoom in
Previous page
1/76
Next page
11
Lithium-ion Brushless Impact Driver EN
LED Light Indicator
Before operation, the LED light
will be activated when the On/
Off switch is slightly depressed,
and will automatically turn off 20
seconds after the On/Off switch is
released.
The tool and battery are
equipped with a protection
system. When the LED Light
is quickly flashing 3 seconds
and turn off, the system will
automatically cut off power to
the tool to extend battery life.
The tool will automatically stop
during operation if the tool and/
or battery are placed under one
of the following conditions:
Overloaded: The tool is
operated in a manner that causes
it to draw an abnormally high
current. In this situation, release
the Trigger Switch on the tool and
stop the application that caused
the tool to become overloaded.
Then pull the Trigger Switch
again to restart.
Overheated: Under the
condition above, if the tool does
not start, the Tool and Battery are
overheated. In this situation, let
the Tool and Battery cool before
pulling the Trigger Switch again.
Low battery voltage: The
remaining Battery capacity is too
low and the tool will not operate.
In this situation, remove and
recharge the Battery.
Warning:
To turn on the light, press
the On/Off switch and make sure
the Forward/Reverse Rotation
Control is on right/left position.
See Fig. E
TROUBLE SHOOTING
1. I CAN NOT FIT THE BATTERY INTO
THE BATTERY CHARGER. WHY?
The battery can be inserted into the charger
only in one direction. Turn the battery around
until it can be inserted into the slot, the red
LED Light should turn on when the battery is
charging.
2. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, as above, and
having not used a Battery Pack for a
prolonged time will reduce the Battery Pack
working time. This can be corrected after
several charge and discharge operations by
charging & working with your drill. Heavy
working conditions such as large screws
into hard wood will use up the Battery Pack
energy faster than lighter working conditions.
Do not re-charge your Battery Pack below
0
o
C and above 30
o
C as this will affect
performance.
MAINTENANCE
Your power tool requires no additional
lubrication or maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation
slots clean. Keep all working controls free
of dust. Occasionally you may see sparks
through the ventilation slots. This is normal
and will not damage your power tool.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or retailer for
recycling advice.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX292.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX292.1 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info