673232
7
Zoom out
Zoom in
Previous page
1/64
Next page
7
Lithium-Ion Cordless Impact Driver EN
xINR18/65-y: Cylindrical lithium
Ion battery cells with max diameter
of 18mm and max height of 65mm;
“x” represents a number cells serial
connected, blank if 1; “-y” represents
a number of cells paralleled
connected, blank if 1
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE:
This tool is intended for the fastening and loosening
of bolts, nuts and various threaded fasteners. This
tool is not intended for use as a drill.
ASSEMBLY AND
OPERATION
ACTION FIGURE
BEFORE OPERATION
Removing the battery pack
See Fig A1
Charging the battery Pack
See Fig.A2
Installing the battery pack
See Fig.A3
ASSEMBLY AND ADJUSTMENT
Inserting and Removing Bits and
Socket
See Fig.B
Forward/Reverse/Lock
WARNING: Never change the
direction of rotation when the
chuck is rotating, wait until it is
stopped!
See Fig.
C1,C2,C3
OPERATION
Operating the On/Off Switch
WARNING: Do not operate for
long periods at low speed
because excess heat will be
produced internally.
See Fig. D
Light Indicator
Before operation, the light will be
activated when the On/Off switch is
slightly depressed, and will automati-
cally turn off 10 seconds after the On/
Off switch is released.
The tool and battery are equipped
with a protection system. The Light
will quickly flash (approximately once
a second, and stop flashing when
you release the trigger ) , the system
will automatically cut off power to
the tool to extend battery life. The
tool will automatically stop during
operation if the tool and/or battery
are placed under one of the following
conditions:
• Overloaded: The tool is operated
in a manner that causes it to draw
an abnormally high current. In this
situation, release the Trigger Switch
on the tool and stop the application
that caused the tool to become
overloaded. Then pull the Trigger
Switch again to restart.
• Overheated: Under the condition
above, if the tool does not start, the
Tool and Battery are overheated. In
this situation, let the Tool and Battery
cool before pulling the Trigger Switch
again.
• Low battery voltage: The
remaining Battery capacity is too low
and the tool will not operate. In this
situation, remove and recharge the
Battery.
WARNING:
To turn on the light, press the
On/Off switch and make sure the
Forward/Reverse Rotation Control is
on right/left position.
See Fig. D
MAINTENANCE
Remove the battery pack from the tool
before carrying out any adjustment,
servicing or maintenance.
Your power tool requires no additional lubrication
or maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to
clean your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place. Keep
the motor ventilation slots clean. Keep all working
controls free of dust. Occasionally you may see
sparks through the ventilation slots. This is normal
and will not damage your power tool.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX290 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info