Manual Worx WX23AG.2 (page 9 of 156) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575105

Zoom out

Zoom in

1/156

Angle grinder EN

SAFETY INSTRUCTIONS

FOR ALL OPERATIONS:

Safety Warnings Common for Grinding or

Abrasive Cutting-Off Operations:

a) This power tool is intended to

function as a grinder or cut-off

tool. Read all safety warnings,

instructions, illustrations and

speciﬁcations provided with this

power tool. Failure to follow all

instructions listed below may result in

electric shock, ﬁre and/or serious injury.

b) Operations such as sanding,

wire brushing, polishing are not

recommended to be performed with

this power tool. Operations for which

the power tool was not designed may

create a hazard and cause personal injury.

c) Do not use accessories which

are not speciﬁcally designed

and recommended by the tool

manufacturer. Just because the

accessory can be attached to your power

tool, it does not assure safe operation.

d) The rated speed of the accessory

must be at least equal to the

maximum speed marked on the

power tool. Accessories running faster

than their rated speed can break and ﬂy

apart.

e) The outside diameter and the

thickness of your accessory must

be within the capacity rating of your

power tool. Incorrectly sized accessories

cannot be adequately guarded or

controlled.

f) Threaded mounting of accessories

must match the grinder spindle

thread. For accessories mounted

by ﬂanges, the arbour hole of the

accessory must ﬁt the locating

diameter of the ﬂange. Accessories

that do not match the mounting hardware

of the power tool will run out of balance,

vibrate excessively and may cause loss of

control.

g) Do not use a damaged accessory.

Before each use inspect the

accessory such as abrasive wheels

for chips and cracks backing pad

for cracks, tear or excess wear,

wire brush for loose or cracked

wires. If power tool or accessory

is dropped, inspect for damage or

install an undamaged accessory.

After inspecting and installing an

accessory, position yourself and

bystanders away from the plane of

the rotating accessory and run the

power tool at maximum no-load

speed for one minute. Damaged

accessories will normally break apart

during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety

glasses. As appropriate, wear dust

mask, hearing protectors, gloves and

workshop apron capable of stopping

small abrasive or workpiece

fragments. The eye protection must

be capable of stopping ﬂying debris

generated by various operations . The

dust mask or respirator must be capable

of ﬁltrating particles generated by your

operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance

away from work area. Anyone

entering the work area must wear

personal protective equipment.

Fragments of workpiece or of a broken

accessory may ﬂy away and cause injury

beyond immediate area of operation.

j) Hold power tool by insulated

gripping surfaces only, when

performing an operation where

the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may

make exposed metal parts of the power

tool “live” and could give the operator an

electric shock.

k) Position the cord clear of the

spinning accessory. If you lose control,

the cord may be cut or snagged and

your hand or arm may be pulled into the

spinning accessory.

l) Never lay the power tool down

until the accessory has come to a

complete stop. The spinning accessory

may grab the surface and pull the power

tool out of your control.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX23AG.2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX23AG.2 Manual

Product: