575041

Worx WX163.3 Manual

11
Zoom out
Zoom in
Previous page
1/136
Next page
Lithium-Ion cordless drill/driver EN
11
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for driving in and
loosening screws as well as for drilling in
wood, metal and plastic.
BEFORE PUTTING INTO OPERATION
A) CHARGING THE BATTERY
The battery charger supplied is matched to
the Li-Ion battery installed in the machine.
Do not use another battery charger.
The Li-Ion battery is protected against deep
discharging. When the battery is empty,
the machine is switched off by means of a
protective circuit: The tool holder no longer
rotates.
In a warm environment or after heavy use,
the battery pack may become too hot to
permit charging. Allow time for the battery to
cool down before recharging.
When the battery pack is charged for the first
time and after prolonged storage, the battery
pack will accept a 100% charge after several
charge and discharge cycles.
B) TO REMOVE OR INSTALL BATTERY
PACK (See Fig. A)
Depress the battery pack release button to
release and slide the battery pack out from
your tool. After recharge, slide it back into
your tool. A simple push and slight pressure
will be sufficient.
OPERATION
1. ON / OFF SWITCH (See Fig. B)
Depress the On/Off switch to start and
release it to stop your drill. The on/off switch
is fitted with a brake function which stops
your chuck immediately when you quickly
release the switch.
It is also a variable speed switch that delivers
higher speed and torque with increased
trigger pressure. Speed is controlled by the
amount of switch trigger depression.
WARNING: Do not operate for
long periods at low speed because
excess heat will be produced internally.
2. SWITCH LOCK
The switch trigger can be locked in the OFF
position. This helps to reduce the possibility
of accidental starting when not in use. To
lock the switch trigger, place the rotation
control in the center position.
3. REVERSIBLE (See Fig. C1, C2)
For drilling and screw driving use forward
rotation marked “
” (lever is moved to the
left). Only use reverse rotation marked
“ ” (lever is moved to the right) to remove
screws or release a jammed drill bit.
WARNING: Never change the
direction of rotation when the
chuck is rotating, wait until it has
stopped!
4. TWO-SPEED GEAR CONTROL
(See Fig. D)
The drill has a two-speed gear control
designed for drilling or driving at LO (mark
is 1) or HI (mark is 2) speeds. A slide switch
is located on top of the drill to select either
LO or HI speed. When using the drill in the
LO speed range, the speed will decrease and
the drill will have greater power and torque.
When using the drill in the HI speed range,
the speed will increase and the drill will have
less power and torque.
Gear I
Low speed range: for screwdriving or
working with large drilling diameter
Gear II
High speed range: for working with small
drilling diameter
WARNING: To prevent gear
damage, always allow the chuck
to come to a complete stop before
changing the direction of rotation or
the two-speed gear control.
5. CHUCK ADJUSTMENT (See Fig. E)
To open the chuck jaws rotate the front
section of the chuck. Insert the drill bit
between the chuck jaws and rotate the front
section in the opposite direction. Ensure the
drill bit is in the center of the chuck jaws.
Finally, firmly rotate the front chuck section
in the opposite directions. Your drill bit is
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX163.3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX163.3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info