575037

Worx WX160.4 Manual

12
Zoom out
Zoom in
Previous page
1/136
Next page
Lithium-Ion cordless drill/driver EN
12
now clamped in the chuck.
6. TORQUE ADJUSTMENT (See Fig. F)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring. The torque is greater when
the torque adjustment ring is set on a higher
setting. The torque is less when the torque
adjustment ring is set on a lower setting.
Make the setting as follows:
1 - 4 for driving small screws
5 - 9
for driving screws into soft mate-
rial
10 - 14
for driving screws into soft and
hard material
15 - 19 for driving screws into hard wood
20 - 23 for driving larger screws
for heavy drilling
7. AUTOMATIC SPINDLE LOCK
(See Fig. G)
The automatic spindle lock allows you to use
it as a regular screwdriver. You can give an
extra twist to firmly tighten a screw, loosen
a very tight screw or continue working
when the battery energy has expired. For
manual screwdriver purposes, the chuck is
automatically locked when the tool is off.
8. USING THE SIGHT LIGHT
The sight light allows you to keep a clear
view under less illuminated circumstances.
To turn on the light simply press the on/off
switch. When you release the on/off switch,
the light will go out.
9. LEVEL DRILLING (See Fig. H)
The bubble level is recessed in the motor
housing on the top of the drill. It can be
used to keep the drill level during horizontal
drilling operation.
The bubble level is recessed in the motor
housing on the back of the drill. It can be
used to keep the drill level during vertical
drilling operation.
10. DRILLING
When drilling into a hard smooth surface,
use a center punch to mark the desired hole
location. This will prevent the drill bit from
slipping off center as the hole is started. Hold
the tool firmly and place the tip of the bit at
the point to be drilled. Depress the switch
trigger to start the tool. Move the drill bit
into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force
or apply side pressure to elongate a hole.
Tungsten carbide drill bits should
always be used for concrete and
masonry. When drilling in metal, only
use HSS drill bits in good condition.
Always use a magnetic bit holder (not
included) when using short screwdriver
bits. When screw-driving, apply a small
quantity of liquid soap or similar to the
screw threads to ease insertion.
11. DISPOSAL OF AN EXHAUSTED
BATTERY PACK
To preserve natural resources, please
recycle or dispose of the battery
pack properly. This battery pack
contains Lithium batteries. Consult your local
waste authority for information regarding
available recycling and/or disposal options.
Discharge your battery pack by operating
your drill, then remove the battery pack
from the drill housing and cover the battery
pack connections with heavy-duty adhesive
tape to prevent short circuit and energy
discharge. Do not attempt to open or remove
any of the components.
12. OVERLOAD PROTECTION
When overloaded, the motor comes to
a stop. Relieve the load on the machine
immediately and allow cooling for approx. 30
seconds at the highest no-load speed.
13. TEMPERATURE DEPENDENT
OVERLOAD PROTECTION
When using as intended for the power tool
cannot be subject to overload. When the
load is too high or the allowable battery
temperature of 75°C is exceeded, the
electronic control switches off the power
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX160.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX160.4 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info