575001
11
Zoom out
Zoom in
Previous page
1/96
Next page
11
Lithium-Ion Cordless Drill/Driver EN
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for driving in and
loosening screws as well as for drilling in
wood, metal and plastic.
ASSEMBLY AND OPERATION
Action Figure
BEFORE OPERATION
Removing the battery pack See Fig. A1
Charging the battery See Fig. A2
Installing the battery pack See Fig. A3
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger
switch and disconnect tool from power
source when changing accessories. Always
ensure the bit is secure before starting the tool.
Damage to the Chuck or a loose bit may cause
possible personal injury.
--Removing the bits See Fig. B2
--Inserting the bits See Fig. B1
OPERATION
Forward/reverse rotation
control
WARNING: Never
change the direction
of rotation when the
chuck is rotating, wait
until it has stopped!
See Fig. C1,
C2, C3
TWO-SPEED GEAR
CONTROL
See Fig. D
TORQUE ADJUSTMENT
DRILLING,SCREWDRIVING,
HAMMER DRILLING
See Fig. E
Operating the on/off switch
WARNING: Do not
operate for long
periods at low speed
because excess heat will
be produced internally.
See Fig. F
LED Light Indicator
Before operation, the LED light will be
activated when the On/Off switch is slightly
depressed, and will automatically turn off 20
seconds after the On/Off switch is released.
The tool and battery are equipped with a
protection system. When the LED Light is
quickly flashing 3 seconds and turn off, the
system will automatically cut off power to
the tool to extend battery life. The tool will
automatically stop during operation if the tool
and/or battery are placed under one of the
following conditions:
Overloaded: The tool is operated in a
manner that causes it to draw an abnormally
high current. In this situation, release the
Trigger Switch on the tool and stop the
application that caused the tool to become
overloaded. Then pull the Trigger Switch again
to restart.
Overheated: Under the condition above, if
the tool does not start, the Tool and Battery are
overheated. In this situation, let the Tool and
Battery cool before pulling the Trigger Switch
again.
Low battery voltage: The remaining
Battery capacity is too low and the tool will not
operate. In this situation, remove and recharge
the Battery.
WARNING: To turn on the light, press
the On/Off switch and make sure the
Forward/Reverse Rotation Control is on
right/left position.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX152.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX152.1 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info