673215
21
Zoom out
Zoom in
Previous page
1/24
Next page
21
LED LIGHT INDICATOR (9)
Before operation, the LED light will be
activated when the On/Off switch is
slightly pressed, and will automatically
turn off 20 seconds after the On/Off switch
is released.
The tool and battery are equipped with a
protection system. When the LED Light
is quickly flashing 3 seconds and turn
off, the system will automatically cut off
power to the tool to extend battery life.
The tool will automatically stop during
operation if the tool and/or battery
are placed under one of the following
conditions:
• Overloaded: The tool is operated
in a manner that causes it to draw an
abnormally high current. In this situation,
release the Trigger Switch on the tool
and stop the application that caused the
tool to become overloaded. Then pull the
Trigger Switch again to restart.
• Overheated: Under the condition
above, if the tool does not start, the
Tool and Battery are overheated. In this
situation, let the Tool and Battery cool
before pulling the Trigger Switch again.
• Low battery voltage: The remaining
Battery capacity is too low and the tool
will not operate. In this situation, remove
and recharge the Battery.
WARNING: To turn on the light,
press the On/Off switch and make
sure the Forward/Reverse Rotation
Control is on right/left position.
See Fig. F
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN
YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is on top of
the trigger, is positioned in the lock function. Unlock the
forward/reverse rotation control by putting it into the
required rotation position. Push the trigger and the drill
will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque adjusting
ring, you can find the torque-adjusting ring between
the chuck and the drill body. Position 1 is the lowest
torque (screw driving force) and position 15 is the
highest torque (screw driving force). Position
is for
drill operation. Regulate the torque adjusting ring to a
higher position to reach the best result.
3. REASONS FOR DIFFERENT BATTERY PACK
WORKING TIMES
Charging time problems, as above, and having not
used a battery pack for a prolonged time will reduce the
battery pack working time. This can be corrected after
several charge and discharge operations by charging &
working with your drill. Heavy working conditions such
as large screws into hard wood will use up the battery
pack energy faster than lighter working conditions. Do
not re-charge your battery pack below 0°C and above
45°C as this will affect performance.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX128.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX128.4 in the language / languages: English as an attachment in your email.

The manual is 4,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info