575154

Worx WX041 Manual

6
Zoom out
Zoom in
Previous page
1/76
Next page
Heat gun EN
76
OPERATION
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The unit is intended for the forming and
welding of plastic, removal of paint and the
warming of heat shrinkable tubing. It is also
suitable for soldering and tinning, loosening
of adhesive joints and the defrosting of water
lines.
PUTTING INTO OPERATION
1. SWITCHING ON/OFF (See Fig. A)
Switching on:
To put into operation, slide the switch (3) to
position I, II or III.
Switching off:
To switch off, slide the on/off switch (3) to the
stop at position 0.
After working for a longer time with high
temperature, allow the unit to cool by running
in the cold air setting I before switching off.
2. THERMO-PROTECTION SWITCH-OFF
When the heater is overloaded (e.g. as a result
of restricted air flow), the unit switches it off
automatically, however, the blower continues
to run. When the unit has cooled to operating
temperature, the heater is switched on again.
3. SETTING THE AIR FLOW AND
TEMPERATURE
The switch (3) can be set to three blower
steps. Suitable air flow and temperature
combinations can be selected according to the
applications.
WX041
Step temperature Airflow
I 50
o
C 300L/min
II 350
o
C 300L/min
III 580
o
C 500L/min
The cold air setting I is suitable for cooling a
warmed work piece or for the drying of paint.
It is also suitable for cooling the unit before
placing down or the changing of nozzles.
The air setting II is suitable for Bending Plastic
and heating shrinking plastic.
The air setting III is suitable for stripping paint
and defrosting pipes.
4. WORKING EXAMPLES
Temperature settings given in the application
examples are suggested values that,
depending on the material characteristics, can
deviate. The distance between the nozzle and
work piece is dependent on the material to be
processed.
The ideal temperature should first be
ascertained by performing a test. Therefore,
begin with a lower temperature setting.
All application examples (except Removing
Paint from Window Frames) can be
performed without accessories. However,
the use of the recommended accessory part
simplifies the work and significantly improves
the quality of the results.
_ Be careful when changing the nozzle, danger
of burning! Do not tough the hot nozzle.
Allow the unit to cool. Wear protective
gloves.
5. SCRAPER (See Fig. B)
The scraper is ideal for stripping paint from
flat wooden surface and edges.
Remember to clean the blade after use with
wire wool and lightly oil before storing.
6. REMOVING PAINT
Choose the required nozzle and fit onto the
heat outlet. Soften the paint using hot air and
remove evenly using a spatula. Do not heat
the paint for too long since this will burn the
paint, making it more difficult to remove.
7. REMOVING PAINT FROM WINDOW
FRAMES
Danger of glass breaking!
Use of the glass protection nozzle is essential.
On profiled surfaces, paint can be removed
using a spatula and brushed off using a soft
wire brush.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX041 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX041 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info