536206
13
Zoom out
Zoom in
Previous page
1/16
Next page
13
Working hints for your tool
Reduce the pressure on the drill bit when it is about to break through.
This will prevent the drill from jamming.
When drilling a large hole, first drill a pilot hole using a smaller drill bit.
Always apply pressure to your drill bit in a straight line, and if possible
at right angles to the workpiece.
Never change the operating mode whilst the drill is running.
Do not apply excessive pressure to the tool when chiseling. Expressive
force does not speed up the work.
Maintenance
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry place. Keep the
motor ventilation slots clean. Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
Trouble shooting
The following table gives checks and actions that you can perform if
your machine does not operate correctly.
If these do not identify/solve the problem, contact WORX Customer
Service.
I would add a comment here to again recommend that you apply
grease to the shank of every drill bit used.
1
2
3
4
5
Symptom Possible Cause Remedy
Machine fails to
operate
No power supply to
machine
Turn power on
Use another socket
The power
and hammer
efficiency of the
machine is low.
Machine may be cold
Warm up the machine
for 1-2 minutes until it
reaches a proper working
temperature
Your drill bit does not slide
freely in the chuck
Clean the dust and debris
inside the chuck; Grease
the shank of the bit if
necessary.
Your drill bit will
not fit into the
chuck easily
The chuck is dirty with
dust and debris.
Clean the dust and debris
from inside the chuck
The shank of the bit is
damaged or distorted
Change a new bit
A drill bit has broken and
the shank has remained
in the chuck
Remove the chuck, and
take out the bit as shown in
Fig.H, then clean the chuck
inside.
You cannot
remove your drill
bit from the chuck
The shank of the bit is
damaged or distorted;
The chuck is dirty with
dust and debris.
Remove the chuck, and
take out the bit as shown in
Fig.H, then clean the chuck
inside.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WU334 900W SDS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WU334 900W SDS in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info