723922
18
Zoom out
Zoom in
Previous page
1/20
Next page
Owner’s Manual of Lawn Mowing Robot EN
18
If you want to re-start it, press and to start mowing.
If an error repeatedly occurs in the same area of your lawn, you might have a problem with the boundary wire. Please
refer to the previous installation instructions and check your set up with its help.
If your lawn is divided in two separate areas connected by a corridor less than 1m, one of which is not provided with
the Charging Base: when Landroid
®
runs out of charge, take it manually to the Charging Base, turn power on by turning
the main switch (8) to “I”(on), press
and , the charge process will start.
If Landroid
®
runs abnormally once in a while, please try to restart it. If the problem is not resolved, try to removing and
reinstalling the battery. If the problem is still not resolved, please contact a WORX.
Do not wash the machine with a high pressure washer. This could cause damage to the battery or the machine.
13. Troubleshooting
If your Landroid
®
does not work correctly, follow the troubleshooting guide below. If the issue persists, contact your Dealer.
Symptom Cause Action
Landroid
®
turns on, but the Blade
Disc does not move.
Landroid
®
is searching for the Charging
Base (unless you press the HOME
button to make it go to the charging
base, or the “Enable boundary cut”
function is operating).
This is normal. Landroid
®
needs to recharge,
the Blade Disc does not rotate while it is
searching for the Charging Base automatically.
Landroid
®
vibrates.
Blades may be damaged. Check
condition of the Blade Disc.
Check the Blades, and replace them if damaged.
Remove debris and foreign objects from the
blades and blade disc.
Grass is being cut unevenly.
Landroid
®
does not work enough hours
per day.
Add more hours to the scheduled mowing
time.
Mowing area is too big.
Try decreasing the size of the mowing area or
adding more hours to the mowing time.
Blades are dull.
Change all the Blades and screws in order to
balance the Bade Disc.
The cutting height is too low for the
length of the grass.
Raise the cutting height and then gradually
lower.
Grass or other object has wrapped
around the blade disc.
Check the Blade Disc and remove the grass
or other object.
There is a build-up of grass in the Blade
Disc or Motor Frame Box.
Make sure the Blade Disc rotates easily. If
need be, you may take off the Blade Disc and
remove the debris.
Your Landroid
®
is inside its
territory and the boundary wire
is connected. The error indication
light flashes red.
The boundary wire ends are clamped
incorrectly.
Reverse the boundary wire ends.
The charging time is far more
than 2h.
Poor connection caused by debris on
the Charging Strip.
Clean the Contact Pins located on the
Charging Base and the Charging Strip on
Landroid
®
using a cloth.
The charging protection program has
activated due to high temperature.
Place the charging base in a shady area or
wait until the temperature has cooled down.
The mower does not charge.
There is no power.
Check the power cord is connected properly
to the charger and the charger is connected
to a suitable power supply.
Does not operate correctly while
manually charging.
Refer to manual charging.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WR106 SI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WR106 SI in the language / languages: English as an attachment in your email.

The manual is 4,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worx WR106 SI

Worx WR106 SI Installation Guide - English - 19 pages

Worx WR106 SI Installation Guide - Dutch - 19 pages

Worx WR106 SI User Manual - Dutch - 21 pages

Worx WR106 SI Installation Guide - French - 19 pages

Worx WR106 SI User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info