723918
12
Zoom out
Zoom in
Previous page
1/20
Next page
Owner’s Manual of Lawn Mowing Robot EN
12
7.2 Burying the Boundary Wire
If you are planning to bury the Boundary Wire, it is recommended to first peg it down. This allows you to easily change the layout
if necessary before burying the wire. When the boundary wire installation is complete, have Landroid
®
follow and check the path
by pressing
and . This will allow Landroid
®
to adjust to its new environment.
While observing Landroid
®
you can easily make alterations to the boundary wire to ensure the Landroid
®
's trouble-free tracking
when locating the charging station. Confirm that Landroid
®
docks in the charging station successfully, and bury the wire if desired.
7.3 Joining the boundary wire
If you want to extend and splice the boundary wire, use a connector. The connector is waterproof and provides optimal
connection.
Insert both wire ends in any two of the three holes of the connector. Insert the wires fully until both wire ends are visible
on the other side of the connector. (See Fig. J1) Press the connector together by using a pair of pliers. (See Fig. J2, J3)
WARNING! It is not recommended to simply splice the boundary wire with insulating tape or use a screw terminal
block for connection. A broken circuit may occur after a period of time as soil moisture can oxidize the wire.
8. Software update
The software can be updated when new versions become available.
The latest software can be downloaded from our website
www.worxlandroid.com. There are two methods to update software.
Method 1: Update via USB. See below for download and
installation instructions:
(1) Locate the latest software version at: www.worxlandroid.com.
Save the file to an empty FAT32 formatted USB (flash drive).
Delete any other files on the drive and check the format. If the
drive is not formatted in FAT32, please reformat the drive.
NOTE: the software update is downloaded as a zipped file. You
will need to unzip or extract it before proceeding.
(2) Place Landroid
®
on a secure and level surface. Turn the Main
Switch to the O” position to turn off your Landroid
®
.
(3) Lift the rear of the Landroid
®
to access the underside.
(4) Open the protective rubber cover under the Landroid
®
to access
the USB port.
(5) Insert the USB drive (flash drive) in the port. (See Fig. K)
(6) Place the Landroid
®
on the ground again.
(7) Turn the Main Switch to the “I” position to turn on the Landroid
®
.
(8) The battery indication light will start to pulse. When the error
indication light flashes blue, the file has been copied.
(9) Without lifting the Landroid
®
, remove the USB drive (flash drive).
(10) The update will begin automatically and may take several
minutes. The final alert sequence will include a beep, and both
the battery indication light and error indication light will flash.
When the error indication light turns off and only the green
J1 J2
J3
K
12


Need help? Post your question in this forum.

Forumrules
1

Forum

worx-wr102-si

Reset search

  • Bonjoiur.
    Nous avons une tondeuse worx 102 SI laquel n'a jamais donné total satisfaction mais...
    Actuellemnt elle tond en marche Ar parfois va en Av, ne fais plus la pelouse de façon complete...
    Un des noteur se bloque lorsque actionne celui-ci a la main. Que puis-je faire pour la rementre en ordre.
    Submitted on 19-4-2022 at 07:17

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WR102 SI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WR102 SI in the language / languages: English as an attachment in your email.

The manual is 4,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worx WR102 SI

Worx WR102 SI Installation Guide - English - 19 pages

Worx WR102 SI Installation Guide - Dutch - 19 pages

Worx WR102 SI User Manual - Dutch - 21 pages

Worx WR102 SI Installation Guide - French - 19 pages

Worx WR102 SI User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info