575063
11
Zoom out
Zoom in
Previous page
1/104
Next page
11
Cordless Li-Ion handy saw
EN
3. REMOVING A SAW BLADE (See Fig. B)
To remove a blade, depress the clamp lever,
pull out the blade.
CHARGING
WARNING: The charger and battery
pack are specially designed to work
together so do not attempt to use any
other devices. Never insert or allow
metallic objects into your charger or
battery pack connections because of an
electrical failure and hazard will occur.
Your battery pack is UNCHARGED and you
must charge once before use
The battery charger supplied is matched to the
Li-Ion battery installed in the machine. Do not
use another battery charger.
1. CHARGING YOUR BATTERY PACK
The Li-Ion battery is protected against deep
discharging. When the battery is empty,
the machine is switched off by means of a
protective circuit. In a warm environment or
after heavy use, the battery pack may become
too hot to permit charging. Allow time for the
battery to cool down before recharging.
2. TO REMOVE OR INSTALL BATTERY
PACK (See Fig. C)
Depress the battery pack release button to
release and slide the battery pack out from
your tool. After recharge, slide it back into your
tool. A simple push and slight pressure will be
sufficient.
OPERATION
1. SAFETY ON/OFF SWITCH (See Fig. D)
Your switch is locked off to prevent accidental
starting. Depress the lock-off button (1) then
the on/off switch (5) and release lock-off button
(1). Your switch is now on. To switch off just
release the on/off switch.
2. WORKING INSTRUCTIONS
NOTE: Hold the machine away from yourself.
Stand in a secure and stable position.
WARNING: Always clamp and
support workpiece securely. Do
not touch blade to workpiece until saw
reaches full operating speed.
HOW TO GRASP YOUR WORX HANDY SAW
Grasp your WORX Handy saw as shown in Fig
E, for best control of the tool and comfortable
use as a reciprocating saw.
GENERAL CUTTING (See Fig. F1, F2)
NOTE:
1. Always use a blade suited to the material
and material thickness to be cut. The quality
of cut will improve as the number of blade
teeth increase.
2. Always ensure the workpiece is firmly held
or clamped to prevent movement. Support
large panels close to the cut line. Any
movement of the material may affect the
quality of the cut.
3. The blade cuts on the upward stroke and
may chip the uppermost surface or edges
of your work piece when cutting, ensure
your uppermost surface is a non-visible
surface when your work is finished.
OPERATION:
1. Mark the line of cut, clearly before your
cutting.
2. Do not force the tool. Place the steel base
(12) firmly on the workpiece while cutting.
Use only enough steady pressure on the
blade to keep the saw cutting.
3. Reduce the pressure as the blade comes to
the end of the cut.
4. Allow the saw to come to a complete stop
when before removing the blade from the
workpiece.
TREE TRIMMING
Use wood blade when cutting tree branches.
Hold steel base firmly against tree brance.
Cut close to the branch of the tree to decrease
movement of the branch being cut.
METAL CUTTING
Use a finer tooth blade for ferrous metals and
a coarse tooth blade for non-ferrous metals.
When cutting thin sheet metals always clamp
steel on both sides of the sheet to reduce
vibration or tearing of the sheet metal. Do not
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WG894E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG894E in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info