Manual Worx WG169E.9 (page 13 of 148) (English, German, Dutch, French, Italian, Polish, Spanish)

576038

Zoom out

Zoom in

1/148

3-in-1 Grass Trimmer/Edger

2. CHARGING YOUR BATTERY PACK

The Li-Ion battery is protected against deep

discharging. When the battery is empty,

the trimmer will switch off by means of a

protective circuit: The trimmer head will stop

rotating.

NOTE: In a warm environment or after heavy

use, the Battery Pack may become too hot to

permit charging. Allow time for the battery to

cool down before recharging.

3. TO REMOVE OR INSTALL BATTERY

PACK (See Fig. C)

Depress the battery release button to remove

Battery Pack (2) from your trimmer. After

recharging, insert the Battery Pack onto

trimmer’s battery bracket. A simple push and

slight pressure will be sufﬁcient.

4. SAFETY ON/OFF SWITCH (See Fig. D)

The safety switch is locked off to prevent

accidental starting. Depress the Lock Off

Button (9) then depress the On/Off Switch (10)

and release Lock Off Button. Your trimmer is

now on. To switch off, just release the on/off

switch.

WARNING! The cutting head

continues to rotate after the

trimmer has been switched off; wait until

it has completely stopped then lay down

the tool.

5. ADJUSTMENT OF THE TELESCOPIC

SHAFT (See Fig. E)

Step one foot on the Safety Guard, then

use one hand to pull up the Telescopic Shaft

Adjustment Trigger (8), adjust the length of

the Telescopic Shaft to the most comfortable

length. Release the Telescopic Shaft

Adjustment Trigger to lock in position.

6. MAIN HANDLE ROTATION (See Fig.

F1, F2)

First, hold down the lower housing with your

foot and pull upward on the Upper Shaft (15).

Then rotate the Upper Shaft clockwise 90

degrees (See Fig.F1) and release; the Shaft

will be locked in position automatically (See

Fig. F2).

7. ADJUSTMENT OF AUXILIARY HANDLE

Pull up the Auxiliary Handle Locking Lever (11).

Hold the Locking Lever and rotate the Auxiliary

Handle to the most comfortable and balanced

position (See Fig. G)

Release the lever, your Auxiliary Handle has

been locked.

8. ADJUSTMENT OF THE TRIMMER

HEAD ANGLE TO THE SHAFT

WARNING! Make Sure the Safety

Switch is Locked Off to Prevent

Accidental Starting.

To adjust the Upper Shaft angle or convert the

tool from trimming mode and edging mode,

unlock the Pivot Head Locking Knob by hand,

and using adequate force, pull the trimmer

head into the desired position, then lock the

Pivot Head Locking Knob.

9. FLOWER GUARD/EDGE GUIDE

Pull the Flower Guard/Edge Guide out before

trimming, as shown in Fig. I1.

When edging, pull Flower Guard/Edge Guide

out also, and keep to a side (See Fig. I2).

Before trimming or edging make sure the

ﬂower guard is locked ﬁrmly in position.

OPERATION

WARNING! Always wear the eye

protection. Never lean over the

trimmer head. Rocks or debris can

ricochet or be thrown into eyes and face

and cause blindness or other serious

injury. When operating unit, check for the

following:

Wear eye protection and heavy clothing.

Hold front handle with one hand and

Auxiliary Handle with the other hand.

Keep unit below waist level. Work only

from your right to your left to ensure

debris is thrown away from you. Without

bending over, keep line near and parallel

to the ground (perpendicular when

edging) and not crowded into material

being cut.

WARNING!

Make sure that line is

fed out before operation. Make sure

motor is up to full speed before trimming

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG169E.9 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WG169E.9 Manual

Product: