576035

Worx WG169.9 Manual

14
Zoom out
Zoom in
Previous page
1/148
Next page
14
3-in-1 Grass Trimmer/Edger
EN
or edging.
WARNING!
Only use 1.65mm
diameter cutting line. Other sizes of
line will not feed properly and will result
in improper cutting head function or can
cause serious injury. Do not use other
material such as wire, string, rope, etc.
Wire can break off during cutting and
become a dangerous projectile that can
cause serious injury.
EDGE /TRIMMING SUPPORT WHEELS
There are three optional positions for the Edge
/Trimming Support Wheels to attach when
assisting in Trimming and Edging.
Position 1: Using the guide wheels when
trimming in a forward or reverse direction
(See Fig. J1)
Position the Grass Trimmer in the trimming
position. Underneath the Safety Guard there is
a metal plate that the Edge/Trimming Support
Wheels will attach to. Slide the Support
Wheels horizontally onto the metal plate until
they lock into position so both the wheels are
facing in the forward direction (See Fig. B3).
The wheels should provide support when
you are trimming in the forward or reverse
direction.
Position 2: Using the guide wheels when
trimming Side to Side
Position the Grass Trimmer in the trimming
position. Underneath the Safety Guard there
is a metal plate that the Edge/Trimming
Support Wheels will attach to. Slide the
Support Wheels vertically onto the metal plate
until it locks into position (See Fig. B2). The
wheels should provide support when you are
trimming in a horizontal side to side direction
(See Fig. J2).
NOTE: you could also use the machine
without the guide wheels on guard when
trimming.
Position 3: Using the guide wheels when
edging (See Fig. I2)
WARNING: Make Sure the Safety
Switch is Locked Off to Prevent
Accidental Starting.
Change the tool from trimming into the
edging mode, the Edge /Trimming Support
Wheels (12) will attach on the side the trimmer
head as shown in Fig. B1.; rotate the main
handle as described in ‘’MAIN HANDLE
ROTATION’’, then unlock the Pivot Head
Locking Knob, and using adequate force, pull
the trimmer head into the desired position.
Make sure to adjust the trimmer head angle
to be in the lowest horizontal setting. Finally,
lock the Pivot Head Locking Knob (See Fig. H3)
and position the wheels on the ground for the
edging mode. While edging, keep the Flower
Guard/Edge Guide aligned with the sidewalk
edge, this will assist to edge in a straight path.
Only the tip of the line will make contact with
area being worked on. Do not force the line.
The edging wheels help protect the unit and
keep the unit from contacting the ground. Take
extra caution while edging, as objects can be
thrown from the trimmer line.
AUTOMATIC LINE FEED SYSTEM
When initially switching on the trimmer, a
small length of line is fed out. Each time the
tool is started from rest it will advance about
6.35mm of trimmer line.
A ‘clattering’ noise will be heard when the
lines hit the Line Cutter. DO NOT BE ALARMED
this is quite normal. After about 5 seconds
the line will be cut to the correct length and
the noise will reduce as the motor gains full
speed.
If the noise of the line being cut can’t be
heard, more line will need to be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely; it must come
to a complete rest, then restart, allowing the
motor to reach full speed.
Repeat above until you hear the line hitting
against the Line Cutter.
TO MANUALLY FEED THE LINE
(See Fig. K1)
Turn off the trimmer and remove the battery.
If required, line can be fed out manually.
To operate, press and release manual Line
Feed Button (17), while gently pulling out the
line until it is long enough to reach the Line
Cutter.
If the line extends past the Line Cutter, too
much line has been fed out.
If too much line is fed out, remove the Spool
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WG169.9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG169.9 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info