724649
9
Zoom out
Zoom in
Previous page
1/18
Next page
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: DBAF50/40 • 61420 • 07/2018
16 17
Important information – Product care
NOTE: Xnity Battery and Charger not included. For any issues related
directly to your purchased ALDI Xnity Battery / charger, contact the
Customer Service of the manufacturer as listed on the battery / charger
packaging, manual or on the label on the battery / charger.
This Brad Nailer / Stapler uses Lithium Ion Battery Cells. Care MUST be taken to
ensure both the safety and life of the pack is maintained. Ensure you have read all
of the safety notes in the previous pages before using the Brad Nailer / Stapler.
Treat the battery pack with care and within the guidelines of this manual and the
supplied manual included with the purchase of ALDI Xnity Battery/s.
If the battery pack does become immersed in water or any uids, or is subject
to a severe drop or it does not operate within the guidelines of this manual
or the supplied manual included with the purchase of ALDI Xnity Battery/s,
immediately STOP using the battery pack and have it checked. During operation
avoid overloading the Brad Nailer / Stapler. If the Brad Nailer / Stapler is
overloaded it will automatically STOP. Overloading may occur for a number of
reasons including when the Brad Nailer / Stapler is pushed too hard or when
using a Nail / Staple greater than what is specied, or there is a nail / staple jam. If
you do overload the Brad Nailer / Stapler during operation refer to the “Overload
Protection” section in this manual.
NOTE: When the battery of the Brad Nailer / Stapler is at the lower end of the
charge, the Brad Nailer / Stapler is more susceptible to the overload condition.
Running the Brad Nailer / Stapler at close to maximum load, or continual resetting
of the overload will cause the battery pack to overheat. When a preset cell
temperature is detected, the battery pack will automatically STOP operating and
will not restart until the battery pack has cooled to a safe level.
In this condition, DO NOT force the cooling down of the pack by placing in a
freezer or similar device. Refer to the “Overload Protection section in this manual.
Another feature of the Brad Nailer / Stapler is the low voltage cut out feature. This
feature operates when the voltage drops below a preset value. When this occurs
the tool will automatically stop operating. To correct the situation you need to
either insert another charged battery into the Brad Nailer / Stapler or recharge the
existing battery, and then proceed with the Brad Nailer / Stapler application.
NOTE: Attempting to restart the tool in this condition without either recharging
the battery or installing a battery with charge will lead to Brad Nailer / Stapler
restarting and then stopping again after only a few seconds of operation.
These safety devices have been tted for the safety, reliability and life of the tool.
Assembly
Fitting and removing the Battery from the Brad Nailer /
Stapler and Charger.
NOTE: (Xnity Battery pack and charger is not included with
this product; it is shown only for illustrative and instructional
purposes only)
1. To install your purchased Xnity battery (17) on to the Brad Nailer /
Stapler, align the grooved guide rails of the battery (17) with the raised
guide rails on the bottom of the Brad Nailer / Stapler. With your thumb
on the battery release tab on the battery pack, slide it rmly into the
handle until the battery is secure in position (Fig A). Release your thumb
from the battery release tab. When the battery is secured you will hear it
engage with a snap / click.
2. To remove the battery (17) from the Brad Nailer / Stapler, press the
battery pack release button and slide the battery (17) completely out
and away from the Brad Nailer / Stapler (Fig B).
3. When applying the battery (17) onto your purchased Xnity charger
(18), align the grooved guide rails of the battery (17) with the raised
guide rails on the charger (18) (Fig C). The charger (18) will make a snap
/ click noise when it is securely aligned.
A. B.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone TG212T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone TG212T in the language / languages: English as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info