724651
13
Zoom out
Zoom in
Previous page
1/18
Next page
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018
24 25
Impact Wrench Safety Features
Impact Wrench Overload
This Impact Wrench is tted with an overload protection. If the Impact
Wrench is excessively forced, or the task being performed is too great
for the Impact Wrench , the Impact Wrench will automatically go into an
overload mode. When the Impact Wrench goes into overload, the Impact
Wrench will automatically and suddenly STOP. To reset the overload,
simply release the trigger switch (5). When the trigger is pressed again,
the Impact Wrench will restart. Resume work after the overload has been
reset, but reduce the load by using a smaller Impact Wrench bit or
CAUTION: Do not continue to overload the Impact Wrench and constantly
reset the overload. Doing this will cause the battery cells to over heat.
Temperature cut out
If the Impact Wrench is constantly overloaded, or the Impact Wrench
is used constantly at maximum rating in high ambient conditions, the
battery cells may overheat causing the battery pack to shut down.
When this occurs you will need to allow the battery cells to cool.
NOTE: The Impact Wrench will not restart until the battery pack has
cooled.
To reduce the temperature of the cells remove the battery pack from the
Impact Wrench and place the battery pack in a free air environment, out of
direct sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators or
freezers.
When the battery pack has cooled down it can again be used to operate
the Impact Wrench, as long as the load or the conditions causing the
original excessive temperature has been corrected.
Low voltage cut out
This Impact Wrench is tted with a low voltage cut out feature.
The low voltage cut out feature operates when the voltage drops below
a preset value. This feature automatically stops the Impact Wrench from
operating (similar to that of the overload condition). When this condition
occurs you will need to either insert another battery into the Impact
Wrench or recharge the existing battery.
The low voltage cut out feature has been added to maximise the life of the
battery cells. When this occurs, recharge the battery pack (6) by following
the battery charging section in this manual or the supplied manual from
your ALDI Xnity purchased charger.
NOTE: Attempting to restart the Impact Wrench without either recharging
the battery or installing another battery (with charge) will lead to Impact
Wrench restarting and then stopping again, after only a few seconds of
operation.
NOTE: For any issues related directly to your purchased ALDI Xnity
Battery / charger, contact the Customer Service of the manufacturer
as listed on the battery / charger packaging, manual or on the label
on the battery / charger.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone IW36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone IW36 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info