724617
26
Zoom out
Zoom in
Previous page
1/32
Next page
16V Lithium-ion Cordless Drill
AFTER SALES SUPPORT
(toll free)MODEL No.: CDT214XA • 05/2019 • 1956
e-mail: info.aldi@positecgroup.com
AUS
24
1300 889 028
AUS
Troubleshooting
Troubleshooting
FAQ/Troubleshooting
Do I need to charge the battery before use?
Yes, new battery packs are usually shipped in a below full charge condition and should be fully
charged before use. It takes approx. 1 hour to fully charge your new battery.
Follow the section in this manual on the details to charge the battery (8). If the charger (10) is
connected to the battery (8) and the green charge indicator light is on and the red light does not
come on, then the battery (8) may already be charged. This does NOT indicate a fault. In this case,
t the battery (8) into the drill and run for approx 3- 5 minutes. Then remove the battery (8) from
the drill reconnect to the battery charger (10). The red light should illuminate. Charge the battery
(8) until the green light comes on.
Follow the full section “Battery Charging “ in this manual on page 14-15.
Charging of batteries should not be undertaken casually. Through the charging cycle the
condition of the battery pack should be monitored and the charge cycle turned o at
completion or at the end of the recommended time.
How do I obtain the best life for the battery?
- Never allow the drill to come to a complete stand still before recharging. The battery should
be placed on charge whenever the battery is noticeably running down or the drill no longer
performs a task it previously performed.
- Avoid allowing lose items like screws or nails etc. to be stored with battery packs as these or
similar items can short battery packs and cause a re or explosion.
- Always unplug the battery charger (10) when not in use and store in a dry secure place.
- Avoid charging or storing your battery in temperatures below 0ºC and above 45ºC.
How do I use the 2 gears on the drill?
To select the LOW gear (low speed, high torque setting), push the gear selector forward, towards
the chuck. The number “1” will be displayed.
To select the HIGH gear (high speed, low torque setting), push the gear selector backwards. The
number “2” will be displayed.
NOTE: The gears cannot be changed if the variable speed / on o trigger (7) is depressed.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone CDT214XA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone CDT214XA in the language / languages: English as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info