809292
12
Zoom out
Zoom in
Previous page
1/32
Next page
12
Controls
Greenstar i ErP – 6 720 806 946 (2015/03)
These are not faults, but provide information concerning the current status of the appliance.
During normal appliance operation various Status codes can be displayed by pressing the button.
The first screen of the Information menu displays the current Status code, this will change as the appliance runs through the various
modes and sequences.
3.1.2 Basic adjust mode
Status code Description
200 Central heating system is being heated.
201 Domestic hot water system is being heated.
202 Anti rapid cycle mode.
The boiler has commenced anti-cycle period for CH. Can be adjusted in boiler settings (2.3b).
Default 5 Minutes
203 System stand by
The appliance is waiting for the heating system to cool.
204 System waiting.
208 Appliance in service Test mode (Min/Max)
265 EMS intelligent controller has forced stan-by-mode due to low heating load.
The appliance is compensating for the power required from the EMS room controller is less than the
minimum output of the boiler).
268 Component test mode.
Appliance is running the manual component test as activated in the menus.
270 Power up mode.
(appliance is powering up).
283 Burner starting.
The boiler prepares for a burner start. The fan and the pump are being controlled.
284 Gas valve(s) opened, flame must be detected within safety time.
The boiler prepares for a burner start. The gas valve is being controlled.
305 Anti fast cycle mode (domestic hot water keep warm function).
Diverter valve is held in hot water position for a period of time (determined by the software) after hot
water demand
309 Central heating and domestic hot water system are being heated.
357 Appliance in air purge mode.
Primary heat exchanger air venting program active - approximately 100 seconds.
358 Three way valve kick.
If the 3-way valve hasn't moved in within 48 hours, the valve will operate once to prevent seizure.
Table 5 Operational status codes
If you see basic adjust mode in the home screen when attempting to make temperature adjustments, the
appliance has been optimised for your heating system and should not need adjustment.
Please use your room thermostat to adjust your heating temperature if you still cannot achieve the desired room
temperature the Installation, Commissioning and Servicing Instructions contain details on how to disable the
basic adjust mode; this will allow further adjustment of the appliances settings.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch Greenstar i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch Greenstar i in the language / languages: English as an attachment in your email.

The manual is 4.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info