809221
10
Zoom out
Zoom in
Previous page
1/20
Next page
Operation
Greenstar 1000 – 6721835944 (2023/08)
10
4.3 Screen display
Fig. 5 Screen display
Table 3
4.4 Displayed Indicators
Indicators displayed on the screen (Tab. 4 and 5):
Table 4 Display indicators
Table 5 Special display indicators
The heating and hot water system has been set up by the installer to its
optimum settings.
It is advised to make a note of these settings before adjusting so that
you can return to these optimum settings in the future.
4.5 Setting the flow temperature
The maximum flow temperature can be adjusted between 30 °C
and 82 °C. The current flow temperature is shown on the display.
Press the ( key.
The set maximum flow temperature is displayed.
Press arrow key or to set the required maximum flow
temperature.
Press the ok key to save. Otherwise the setting will be saved
automatically after 3 seconds.
The display shows the current flow temperature.
The ( symbol flashes in the display in heating mode. The B symbol
also appears if the burner is active.
WARNING
Risk of scalding!
This appliance is supplied with the CH control set at approximately
65 °C, a temperature that should be suitable for most installations
that comply with the current building regulations. When the boiler
switches from CH to DHW, the temperature of the hot water may
briefly exceed the DHW set point if the CH temperature is set higher
than the DHW temperature. If the CH temperature is changed to
above 65 °C, it is advisable to fit a thermostatic mixing valve (TMV) at
the point of use (e.g. before the bath hot tap or shower) to protect
vulnerable people from scalding.
4.6 Setting the DHW heating
4.6.1 Set DHW temperature
DHW temperature:
Press the * key.
The set DHW temperature is displayed.
Press arrow key or to set the required DHW temperature
Press the ok key to save. Otherwise the setting will be saved
automatically after 3 seconds.
The display shows the current flow temperature.
The * symbol flashes in the display in DHW mode. The B symbol also
appears if the burner is active.
Key Explanation
[1] Digital display
Displays a temperature or appliance status/diagnostic code.
[2] Central heating (CH)
( Heating mode On
] Heating mode Off
[3] Fault indicator
Displays during a fault condition.
[4] Burner operation
Displays when the appliance is firing during heating or hot
water mode.
[5] Chimney sweep mode
Displays during service when the appliance is set to
maximum or minimum output.
[6] Service mode
Displays when a qualified service engineer is in the service
menus.
[7] Eco mode active
Displays when in Economy mode (when in Economy mode,
comfort mode is turned off)
[8] Domestic hot water (DHW)
* Hot water mode On
[ Hot water mode Off
Indicated value Introduction
Number, period, number or
letter, letter after dot
Service function
After the letter comes a
number or letter
Error code flashes
Number two or one number,
number after dot
or
Three numbers
Decimal value
eg. boiler temperature
0010042385-001
8 7
21 3 4
6 5
Special
indicator
Introduction
EMS connection not possible
Siphon filling program active (service function)
Air discharge function (approximately 4 minutes)
(service function)
]Summer mode (device frost protection)
Example 227 Error code
only ] and [Standby mode
Low pressure
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch Greenstar 1000 - GR1000W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch Greenstar 1000 - GR1000W in the language / languages: English as an attachment in your email.

The manual is 2.68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info