697462
9
Zoom out
Zoom in
Previous page
1/16
Next page
9
Commissioning
CS200 – 6720830475 (2015/06)
5. Fill and vent the system.
6. Commissioning the CS 200 solar controller
( Chapter 5.2, page 9)
7. Commissioning the system with the solar controller
( Chapter 5.3, page 9)
8. Check and, if necessary, adjust the settings in the service
menu of the CS 200 solar controller and perform
configuration ( Chapter 5.4, page 10)
9. Remedy warning and fault displays, if necessary, and reset
fault history
10. System handover to end user ( Chapter 5.7, page 10).
5.2 General commissioning of the solar controller
Setting the language
Turn the rotary control knob to select a language and press
the rotary control knob.
Setting the date
Turn the rotary control knob to set the day, month and year.
Continue is highlighted.
If the date is set correctly, press the rotary control knob to
apply the date.
Setting the time
Turn the rotary control knob to set the hours and the
minutes.
Continue is highlighted.
If the time is set correctly, press the rotary control knob to
apply the time.
System configuration
Turn and press the rotary control knob to start (Yes) or to
skip the configuration wizard (No).
When the configuration wizard begins, the solar controller
automatically recognises which BUS nodes (e.g. modules)
are installed in the system (system analysis) and adjusts
the menu and the factory defaults to the current system.
Perform system commissioning ( Chapter 5.3).
5.3 System commissioning with the
configuration wizard
The solar controller automatically recognises which BUS nodes
(e.g. modules) are installed in the system. The configuration
wizard adjusts the menu and the factory defaults.
The system analysis may take up to one minute.
After the configuration wizard has performed the system
analysis, the Commissioning menu is opened. The settings
must be checked here and, if necessary, adjusted and finally
confirmed.
If the system analysis is skipped, the Commissioning menu is
opened. The settings listed here must be carefully adjusted
according to the installed system. Finally, the settings must be
confirmed.
For further information on the settings refer to the technical
documentation of the modules used.
5.3.1 Commissioning the solar heating system
Menu item
Start configuration wizard?
Question Answer / setting
Check before starting the configuration wizard:
Module installed and address set?
Temperature sensor installed?
System charged and vented?
Start the configuration
wizard?
Yes | No
Operating mode
Question Answer / setting
Which system is installed?
Is the coding switch
correspondingly set at the
solar module?
Solar | DHW
Extension module
Question Answer / setting
Is an extension module
installed? (only required if
the use of a MS100 is used
in addition to the required
MS 200)
No | MS 100
Change solar configuration
Question Answer / setting
Is the solar thermal system
correctly configured with all
functions and additional
functions?
Graphic configuration of the
solar system
Speed ctrl. solar pump
Question Answer / setting
Is a solar pump with speed
control installed?
No | PWM | 0-10 V
Speed ctrl solar pump2
Question Answer / setting
Is a solar pump with speed
control installed?
No | PWM | 0-10 V
Gross collector area 1
Question Answer / setting
How large is the gross
collector area?
0 to 500 m
2
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch CS 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch CS 200 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worcester-Bosch CS 200

Worcester-Bosch CS 200 User Manual - English - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info