Please check noise abatement regulations prevailing in your country.
• Check the operating tool for
a) tight t of the attachment parts
b) damage or heavy wear and tear - When replacing observe installation instructions
•
Examine line installed on the outside of the tool and the connection cable for damage and wear and tear (brittleness). Only use when no damages can be found.
• Repairs to the cable may only be carried out by a specialist.
• Check the grassbox more often for wear and tear.
• Before adjusting or cleaning of the tool or before checking whether the connection line has been knotted up or damaged switch off the tool and
pull plug out of the socket.
3. Cable
• Please work with safety cables from WOLF. For the connection only lines which are not lighter than rubber hose lines H0 7 RN-F with a minimum
diameter of 3 x 1,5 mm
2
must be used.
• The attachments of the connection cables must be rubber or covered with rubber and comply with Standard DIN/VDE 0620.
• Attachments must be splashproof (applicable in Austria only).
• Use a leakage-protective system (RCD) with a leakage current of no more than 30 mA.
• Attach connection cable to traction relief. Make sure that in does not rub against edges, pointed or sharp objects. Do not squeeze cable through
door or window gaps.
• Switching devices must not be removed or bridged (e. g. tying of switching lever to guide spar).
4. Starting up
• Only switch on motor when your feet are at a safe distance from the cutting tools.
• Do not tilt the aeriator when operating the switch unless absolutely necessary. If it is necessary tilt the aeriator as little as possible and always in
such a way that the aeriator remains between you and the blade.
5. During aeriation - for your safety
• Warning, Danger! Cutting tool is lagging!
• Adhere to the safety distance given by the guidance spars.
• Only switch on motor when your feet are at a safe distance from the cutting tools.
• Always make sure that you have a safe footing, especially on slopes. Never run, always walk slowly.
• Do not use the aeriator on steep slopes.
• Keep cable away from operating tool when aeriating.
• Always move aeriator horizontally to the slope, never up and down.
• Switch off aeriator when tilting or transporting.
• Never use the aeriator when protective devices or housing parts are damaged or missing.
• Before lifting or removing the aeriator switch off motor an wait until the operating tools have come to a complete standstill.
• Before removing the grassbox or adjusting of the operating height switch off motor and wait for the complete standstill of the operating tools.
• Replace worn or damaged blades as a complete set. Observe installation instructions. For safety reasons always use original spare parts.
•
Maintenance and cleaning procedures on the aeriator as well as removing the protective devices may only be carried out when the engine is switched off.
• Never store the aeriator in damp surroundings or near open ame.
• Should have run over an object with the aeriator it should be examined by a specialist (see list of repair shops) for safety reasons.
• If the connection cable is damaged during use it must be disconnected immediately. Do not touch the cable until it is disconnected.
Assembly
Assembling bottom handle part (fig. M1)
Insert securing screw (A) from inside through the left side element, so that both projections catch in the recesses (1). Position
insulation element (B) from outside; the two nubs must catch in the holes of the side element (2). Position handle element (M) in
the insulating element (B). Place insulating element (C) so that the large opening points to the outside. Then press washer (D) into
the opening of the insulating element (C) and tighten wing nut (G).
Assemble the right handle element in the same order.
Assembling top of handle (fig. M2)
Attaching switch, strain relief and clips (fig. M3)
Fold up switch bracket (1) and position switch (H) on the upper handle element so that the two nubs catch in the holes (2). Close
switch bracket (1) and insert cable strain relief (I). Then fasten switch (H) and cable strain relief (I) with the two screws (K). Fasten
switch cable (3) with the clips (L) on the handle rod.
Attaching protective flap (fig. M4)
Place protective flap (O) on the cover (1). Then press retainer slots (2) into the fastening flaps (3) on the cover (1).
Operation
Lawn conditionWorking position
Transport / uneven lawn surface1
Clean lawn surface2
Worn blade3
Setting the working depth (Fig. B1)
The working depth is adjustable to 3 heights (1 = 3 mm, 2 = -3 mm, 3 = -9 mm). Pull adjustment arm (A) away from side cover and
allow to catch in desired position (B). Adjust the height alternately left and right by only 1 position. The adjustment arms must always
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for WOLF-Garten UV 28 EVK at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of WOLF-Garten UV 28 EVK in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.
The manual is 0,69 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
