Manual WOLF-Garten UL 33 E (page 8 of 22) (English, German, Dutch, French, Italian)

638215

Zoom out

Zoom in

1/22

Please check noise abatement regulations prevailing in your Country.

Operating Times

Assembly

Assembling bottom handle part (fig. M1)

Insert securing screw (A) from inside through the left side element, so that both projections catch in the recesses (1). Position insulation

element (B) from outside; the two nubs must catch in the holes of the side element (2). Position handle element (M) in the insulating element

(B). Place insulating element (C) so that the large opening points to the outside. Then press washer (D) into the opening of the insulating

element (C) and tighten wing nut (G).

Assemble the right handle element in the same order.

Assembling top of handle (fig. M2)

Attach upper handle element (N) on the lower handle elements (M), making sure that the holes (1) match. Then insert the connecting screws

from outside, put on the washers (F) and tighten the wing nuts (G).

Attaching switch, strain relief and clips (fig. M3)

Fold up switch bracket (1) and position switch (H) on the upper handle element so that the two nubs catch in the holes (2). Close switch

bracket (1) and insert cable strain relief (I). Then fasten switch (H) and cable strain relief (I) with the two screws (K). Fasten switch cable (3)

with the clips (L) on the handle rod.

Attaching protective flap (fig. M4)

Place protective flap (O) on the cover (1). Then press retainer slots (2) into the fastening flaps (3) on the cover (1).

Operation

General

Before using the machine, the lawn must be mowed to a height of about 2.5-3.5 cm. Remove the cut grass from the lawn. The lawn should be

aerated several times each year. The loosened material can be removed with a rake or catch bag*. Afterwards, the lawn should be fertilized.

* Accessories at additional cost.

Insert connection cable in the strain relief (fig. B2)

Insert coupling of connection cable (3) in the socket of the switch (H). Then guide the cable (4) from outside in a slight loop over the peg (5)

of the strain relief assembly (I).

Connection to the power outlet

(230 Volt AC, 50 Hz). The machine can be connected to any power outlet that is protected by a 10 amp fuse (or line protecting switch type K

- formerly H).

Note:

Use a residual current protection device with a residual current of no more than 30 mA.

Motor on (fig. B2)

Press button (1) and hold.

Lift lever (2) and release button (1).

Motor off (fig. B2)

Release lever (2).

Attaching catch bag* (fig. B3)

Lift protective flap (O). Hang catch bag (1) with the hooks on both bolts** of the side elements.

(* TK 33, accessory at additional cost, ** bolts included with catch bag)

height

(mm)

Moss

Weeds

Grass-

remnants

-3 X ---

4 X ---

8 --- X

Recommended working depths

Setting the working depth (Fig. B1)

The working depth is adjustable to 3 heights. Pull adjustment arm (1) away from side

cover and allow to catch in desired position (2). Adjust the height alternately left and right

by only 1 position. The adjustment arms must always be in the same height position.

Lower and middle position of aerator cylinder:

Removes moss and weeds from the lawn.

Top position of aerator cylinder:

Removes grass remnants from the lawn.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten UL 33 E in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of WOLF-Garten UL 33 E

WOLF-Garten UL 33 E User Manual - English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish - 30 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

WOLF-Garten UL 33 E Manual

Product: