638396

WOLF-Garten TC 38 S Manual

8
Zoom out
Zoom in
Previous page
1/19
Next page
8
Assembly
Included with the delivery
Check the contents of the shipping box when unpacking for,
• Completeness • possible transport damage
Communicate damage claims or missing items immediately to your
dealer, freight forwarder, or manufacturer. Later claims will not be
recognized.
• Lawn mower
•
Handle – lower piece, handle – upper piece, 2 middle pieces
• Bag with mounting parts
• Operating instructions / list of repair shops
Mount handle assembly (Fig. M1 / M2)
Handle – lower piece (1)
Place the handle - lower piece left/right on the sidepieces
and anchor with screws, washers, and lock nuts (TC 30 S),
or wing nuts (TC 32/38 S).
Handle - middle pieces (2)
Place the middle pieces left/right on the handle - lower piece
and anchor with the screws and lock nuts (TC 30 S) or wing
nuts (TC 32/38 S).
Handle – upper piece (3)
Place the handle – upper piece on the middle pieces and
anchor left/right with screws and lock nuts (TC 30 S), or wing
nuts (TC 32/38 S).
Operation
Adjusting the cutting height (Fig. B1)
There are 5 positions for cutting height (18, 23, 28, 32,
40 mm).
Pull the adjusting arm (1) away from the sidepiece and let it
re-engage in the desired cutting height position (2). Adjust, by
1 position only, alternating right and left. The adjustment arms
must always be on the same height position.
Note: Adjust the cutting height so that the bottom blade has
no ground contact if there are uneven areas on the lawn
surface.
Mowing
To maintain a well-groomed lawn, the grass must be cut at
least once a week. The grass must be dry, for the most part,
when it is mowed. The mowing path should be as straight as
possible using a normal walking speed. The mowing paths
must always overlap by several centimetres to prevent strips
of grass being left uncut.
Adjusting the lower blade (Fig. B2)
You must readjust the blade if the mower no longer cuts the
lawn uniformly and cleanly.
Caution: Wear protective gloves.
Turn over the mower as illustrated. Adjust by loosening or
tightening the two lock nuts (3) on the lower blade (4).
Required tools: Spanner (wrench) 10 mm AF.
Turn the lock nut (3) to the left:
The clearance to the blade cylinder (5) decreases.
Turn the lock nut (3) to the right:
The clearance to the blade cylinder (5) increases. Adjust the
lower blade in such a manner that all cutting edges of the
blade cylinder touch lightly.
Cutting test with paper (Fig. B3)
Caution: Wear protective gloves.
The adjustment is correct if a piece of paper between the
blade spindle and the lower blade is cut sharp. To do this
turn the blade cylinder by hand.
Note:
If problem-free cutting results are not obtained, in spite of
adjustment as prescribed, then the blade spindle, and/or the
bottom blade must be checked (see maintenance).
Maintenance
Care and storage
Clean the mower after each use with a hand brush and store
in a dry location. The ball bearing, roller axle and the cutting
edges of the blades should be treated with environmentally
safe, biodegradable spray oil once a year.
Repairs
Always have a WOLF service repair shop handle repairs,
blade cylinder, and bottom blade sharpening, or replace-
ment.
We recommend: Have your mower thoroughly checked once
a year by approved Service Agent.
Please carefully retain the guarantee card completed by the seller,
or the proof of purchase.
The company WOLF-Garten provides a guarantee for 24 months from
the date of purchase. This guarantee is in accordance with the relevant
state of technology and the utilisation purpose / area of application. The
consumer‘s statutory rights are not affected by the following guarantee
guidelines.
Pre-conditions for the 24-month guarantee entitlement:
- Deployment of the device solely for private use.
The guarantee is reduced to 12 months in the commercial sector
or leasing business.
- Proper handling and observance of all information given in the
operating manual, which forms part of our guarantee terms.
- Observance of the prescribed maintenance intervals.
- No unauthorised alteration of the design.
Guarantee terms
- Installation of original WOLF replacement parts / accessories.
- Presentation of the completed guarantee card and/or proof of
purchase.
This guarantee does not extend to normal wear-and-tear on blades,
blade mounting components or friction disks, V-belts/toothed
belts, running wheels/tyres, air filters, spark plugs and spark plug
connectors. Any guarantee claim shall be immediately void in the
event of unauthorised repairs. Faults and defects which can be traced
to material or manufacturing faults will be rectified exclusively by our
contracted workshops (the seller has the right to remedy a defect) in
your vicinity, or by the manufacturer if the latter is closer. Any claims
going beyond the provision of a guarantee are ruled out. There is
no entitlement to a replacement. Any transport damage should be
reported not to us but to the shipper in question since, otherwise, any
compensation claims vis-à-vis the shipper would be voided.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten TC 38 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten TC 38 S in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info