799082
21
Zoom out
Zoom in
Previous page
1/155
Next page
Operation
21
EN
Operating times
ÎObserve the times stipulated in local byelaws.
ÎCheck with your local authorities to determine if
there are any operating time limitations.
Guiding the cable through the strain relief =
The strain relief in the control handle prevents acci-
dental disconnection of the extension cable.
ÎFasten the extension cable in the strain relief as
shown.
Mains socket connection (230 Volt, 50 Hz)
WARNING!
Risk of injuries or material damage.
¾Observe the mains voltage.
¾The power source voltage must
match the information on the device
identi¿cation plate.
¾Only connect to a socket, that is
protected by a 10-16 A slow-blow fuse
(or an MCB).
Note
7KHSURWHFWLYHGHYLFHVSURWHFW\RXDJDLQVW
VHYHUHLQMXU\LQWKHHYHQWRI\RXUFRPLQJLQWR
FRQWDFWZLWKGDPDJHGEDUHZLUHVLIDQ
LQVXODWLRQGHIHFWH[LVWVDQGXQGHUFHUWDLQ
FLUFXPVWDQFHVLIGDPDJHWROLYHZLUHV
occurs.
We recommend that you only connect the
device to power outlets that are protected by
a residual current device (RCD) with a tripping
current of no more than 30 mA.
For older wiring installations, upgrade kits are
available. Consult a quali¿ed electrician.
Switching on/off 7
WARNING!
Risk of injuries due to the rotating line.
ÂTool continues running!
¾Always wait until the cutting tool comes
to a standstill.
¾Hold the trimmer parallel to the lawn
before switching on.
Switching the device on
ÎPress and hold the unlocking button $.
ÎPress the on/o switch %.
ÎRelease the unlocking button.
3The cutting tool is running.
Switching the device o
ÎRelease the on/o switch.
3The cutting tool comes to a standstill after a short
period.
Cutting variants when operating
Cutting small areas of grass ?
ÎHold the device by the upper and middle handles.
ÎSwing the device in semi-circles in front of the
body (without contacting the ground).
Note
7KHRSWLPXPZRUNLQJDQJOHIRUFXWWLQJLV
DERXW&XWWDOOHUJUDVVVORZO\DQGLQ
VWDJHV
Edge cutting <
The edge cutting function enables precise trimming
along the lawn edge.
WARNING!
Risk of injuries due to the cutting tool.
¾Only adjust the device with the motor
switched o and the cutting tool at a
standstill.
ÎPress the locating knob $.
ÎRotate the grass trimmer upper part through 180°
to the left until it audibly engages %.
ÎHold the device by the upper and middle handles.
ÎGuide the device along the lawn edge (without
touching the ground) '.
Adjusting the line ;
ÎPress the running device brieÀy onto ¿rm ground,
e.g. a paving stone using the press knob (pressing
down force about 3 kg). About 1.5 cm of cutting
line is automatically fed out.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten LYCOS E-280 T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten LYCOS E-280 T in the language / languages: All languages as an attachment in your email.

The manual is 3.32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info