799102
28
Zoom out
Zoom in
Previous page
1/249
Next page
Assembly
28
EN
Note
7KHGHYLFHPD\RQO\EHRSHUDWHGLIWKH
PLGGOHKDQGOHLVORFDWHGLQWKHSUHVFULEHG
SRVLWLRQ7KLVPHDQVWKDWLWPXVWEHORFDWHG
EHWZHHQWKHWZRDGMXVWPHQWOLPLWHUVDDQG
WKDWWKHLPSULQWHGDUURZRQWKHIDVWHQLQJ
SLHFHLVDOLJQHGZLWKWKHPDUNLQJOLQHRQWKH
arm.
Adjusting the middle handle <
ÎRelease the nut on the middle handle $.
ÎPush the middle handle to the desired height %
between the two adjustment limiters (a).
ÎAdjust the inclination of the middle handle'.
ÎAlign the middle handle on the arm so that the
imprinted arrow on the fastening piece is aligned
with the marking line on the arm and retighten the
nut #.
Note
7KHGHYLFHPD\RQO\EHRSHUDWHGLIWKH
PLGGOHKDQGOHLVORFDWHGLQWKHSUHVFULEHG
SRVLWLRQ7KLVPHDQVWKDWLWPXVWEHORFDWHG
EHWZHHQWKHWZRDGMXVWPHQWOLPLWHUVDDQG
WKDWWKHLPSULQWHGDUURZRQWKHIDVWHQLQJ
SLHFHLVDOLJQHGZLWKWKHPDUNLQJOLQHRQWKH
arm.
Attaching the carrying belt A7
ÎAttach the carrying belt Ausing the two snap
hooks on the hook of the operating module.
Adjusting the carrying belt ;
ÎAdjust the carrying belt to the desired length. The
attachment hook should be at hip height $.
Note
$OZD\VXVHWKHFDUU\LQJEHOWZLWKWKHGHYLFH
WRJLYH\RXEHWWHUFRQWURORYHUWKHGHYLFH
DQGWRSUHYHQW\RXUDUPVDQGEDFNIURP
tiring too TXLFNO\
Note
)RUVDIHW\UHDVRQVRQO\FDUU\WKHGHYLFH
VXSSRUWHGRYHU\RXUVKRXOGHUDQGQHYHU
DURXQG\RXUQHFN7KHEHOWKDVDTXLFN
UHOHDVHDWWDFKPHQWVRWKDWLWFDQEHTXLFNO\
GLVFRQQHFWHGLQWKHHYHQWRIDPDOIXQFWLRQ
Fitting the cutting blade :
ÎRotate the line head untilthe hole in the spacer is
aligned with the recess of the gear casing.
ÎPush the retaining rod A through the recess in
the hole and hold it tight to lock the thread $.
ÎHold the retaining rod tightly and rotate the line
head clockwise (to the right) from the drive
shaft %/'.
ÎPush the cutting blade Aon to the drive shaft
and position it, centred, on the spacer. Press the
cutting blade tightly home.
Note
(QVXUHWKDWWKHFXWWLQJEODGHLVFHQWUHGDQG
OLHVÀDW
ÎPush the retaining dome A on to the drive shaft
and the cutting blade #.
ÎRotate nut A anticlockwise (left) on the drive
shaft and tighten to a torque of 20 Nm .
Note
%HIRUH¿QDOWLJKWHQLQJFKHFNIRUFRUUHFW
VHDWLQJRIWKHFXWWLQJEODGH+ROGWKHUHWDLQ-
LQJURGZKLOHURWDWLQJDQGWLJKWHQLQJWKHQXW
Note
,IQRWRUTXHZUHQFKLVDYDLODEOHWLJKWHQWKH
QXWZLWKDULQJVSDQQHURUXVLQJWKHVXSSOLHG
ER[VSDQQHUGHSHQGHQWRQWKHPRGHOXQWLO
WKHUHWDLQLQJGRPHLV¿UPO\ORFDWHGDJDLQVW
WKHEODGH7KHQWLJKWHQWKHQXWE\RQHIXOO
turn (360°).
ÎRemove the retaining rod !.
ÎRemove the blade safety cover from the cutting
blade ".
Note
,IQHFHVVDU\UHPRYHWKHHGJHRIWKHSUR-
WHFWLYHFRYHUWRVLPSOLI\ZRUNLQJ5H¿WWKH
HGJHWRWKHSURWHFWLYHFRYHULI\RXDUHXVLQJ
WKHGHYLFHZLWKWKHFXWWLQJOLQH6HHVHFWLRQ
³$VVHPEOLQJWKHSURWHFWLYHFRYHU´
Fitting the line head
ÎRemove the blade in the reverse sequence to that
described in the section “Fitting the cutting
blade” :.
ÎLock the gearbox with the retaining rod Aand
rotate the line head anticlockwise (left) on the
drive shaft.
ÎManually tighten the line head.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten LYCOS 40-230 BC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten LYCOS 40-230 BC in the language / languages: All languages as an attachment in your email.

The manual is 5.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info