638224

WOLF-Garten HS 43 E Manual

9
Zoom out
Zoom in
Previous page
1/54
Next page
9
Assembly
Protection shield - HS 43 / 54 E (Fig. M5)
If screws are fastened to the bottom plate, remove these. Fasten the
hand protector with the two included screws to the bottom plate.
Power connection
The machine can only be connected to a single-phase a.c. current
connection. The machine is protectively insulated in accordance with
classification II of VDE 0740. Before using the machine ensure that the
mains current agrees with the operating voltage data on the machine’s
identification plate.
Power Circuit Breaker
Machines which will be used in different outside locations must be
connected to a Power Circuit Breaker.
Safety Guard - Hs 40 E (Fig. M1)
Fit the enclosed safety guard in the slot on the hedgetrimmer. The safety
shield prevents touching the blades during operation. Hold tool with both
hands!
Mounting the bow-type handle - HS 43 / 54 E (Fig. M2-M4)
If there are screws fixed to the mounting points, remove these first.
Then, remove the shear protector and put the bow-type handle from the
front over the shearing system, and put it into the relief of the hedge
shears’ housing. (If necessary, pull the lower ends of the handle slightly
apart.) Take care that you do not squeeze the two parts of the bow-type
handle.To fasten the bow-type handle screw the two included screws
through the openings in the handle into the threaded holes of the housing
and fasten them tightly.
Operation
Operating times
Please consider the individual country specifications.
Instructions for use of the equipment
Do not use the trimmer in rain or for cutting wet hedges! Check the hedge
trimmer flex and its connections before each and every use for visible
signs of damage (disconnect the power plug)! Do not use a faulty flex.
Gloves
Protective gloves must be worn when using the hedge trimmer.
Securing the extension lead (Fig. B1)
Only use extension leads suitable for outside use. The cross section of
the wire (max. length of extension cord: 75m must be at least 1,5 mm
2
.
Secure the equipment flex to the extension lead by means of a loop.
Extension leads longer than 30 m will reduce the performance of the
machine.
Two-hand safety switch (Fig. B2)
To switch on and to run the hedge trimmer you need both hands: The
switching bar in the rear handle as well as the switch in the front handle
must be depressed (A, B). If one of the switches is released, the shearing
blades will stop after ca. 0.5 seconds HS 40 E, 0.02 seconds HS 43 / 54 E.
Holding the hedge trimmer when in use (Fig. B3, B4)
This equipment will enable you to cut or trim bushes and hedges easily
and comfortably. Trimming of hedges
- Young shoots are best cut in a scythe movement.
- Older and stronger hedges are best cut in a sawing movement.
- Branches, which are too thick for the hedge trimmer, should be cut with
a saw.
- Sides of hedges should be cut upwards in a taper.
In order to achieve an even height
- Fix a guide line at the required height.
- Cut evenly over this guide line.
Expanded working height
If you want to reach higher or if you to above your head’s height, you
should take care of the following:
Attention: Take care to have a secure and safe standing position when
working with your hedge shears in order to avoid slipping and injury.
Always keep the shearing blades away from your body.
Optimum safety
The 5 special features:
two-hand safety switch, quick blade stop, protective cover, blade safety
rail and impact protector are fitted to provide the hedge trimmer with
optimum safety features.
Two-hand safety switch (Fig. B2)
Quick blade stop
In order to avoid injuries through cuts, the blade will stop in max. 0.5 sec. HS
40 E, 0,02 sec., HS 43 / 54 E, when one of the two switches isreleased.
Blade safety rail (Fig. B5)
The cutting blade set back from the blade housing reduces the risk of
injuries due to unintentional body contact. As soon as the hedge trimmer
is switched off, the sharp cutting blades will stop immediately.
Impact protector (Fig. B5, A)
The extended guide rail prevents unpleasant shocks (blade recoil) being
transmitted to the operator due to impact with solid objects (wall, ground etc.)
.
Gear protection feature
If solid objects are caught in the cutting blade and jam the motor, switch
off the machine at once, disconnect the power plug from the power
socket, remove the object and continue with the work. The equipment
is also fitted with an overload cutout, which protects the gears against
mechanical damage in the event of blade jams.
30. Have your power tools repaired by a qualified electrician
- This power tool corresponds to the applicable safety guidelines. Only an
electrician, using original replacement parts, may execute repairs; the use
of non-original replacement parts can cause accidents for the operator.
Safety instructions
31. Never attempt to use a machine that has parts missing, or a machine that has
an unauthorized modification.
32. Never allow children to use the tool.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten HS 43 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten HS 43 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info