Manual WOLF-Garten GT-S 2-27 (page 17 of 83) (English, German, French, Italian, Portuguese, Spanish)

523454

Zoom out

Zoom in

1/83

Installation manual

Installing and setting the handle bar

1. Position the handle bar between the upper and middle

clamp (Fig. 1).

2. Hold the three parts together and screw the four (4) bolts

through the upper clamp into the middle clamp.

Note: The holes in the upper and middle clamps are in align-

ment only if the unit has been assembled correctly.

3. Hold the clamps and the handle bar over the shaft

housing and on the lower clamp.

4. Hold each of the hex nuts in the lower clamp recess with

one finger. Loosely screw in the bolts with a large cross-

head screwdriver. Do not tighten the screws until the

handle bar has been set correctly.

5. Hold the unit in the operating position (Fig. 20) and

position the handle bar until you have a secure footing.

6. Evenly tighten the bolts in the holder until the handle bar

is secure.

Attaching and adjusting the shoulder strap

1. Pull the belt through the buckle (Fig. 3).

2. Pull the shoulder belt over your head and place

the pad on your shoulder.

3. Latch the hook of the shoulder belt into the metal holder

(Fig. 4). Adjust the belt to a comfortable length (Fig. 5).

Using the EZ-Link

system (depending on model)

Note: To facilitate installation and removal of attachments,

place the unit on the ground or a workbench.

Removing the cutting attachment or other

attachments

1. To loosen the attachment, rotate the screw handle

to the left (Fig. 7).

2. Press and hold down the release button (Fig. 7).

3. Hold the upper shaft housing securely and pull

the cutting attachment or other attachment directly

out of the EZ-Link

coupling (Fig. 8).

Installing the cutting attachment or other

attachments (depending on model)

1. To loosen the attachment, rotate the screw handle

to the left (Fig. 7).

2. Hold the attachment securely and push directly into the

EZ-Link

coupling (Fig. 8).

Note: Alignment of the release button with the guide groove

facilitates installation (Fig. 7).

3. Secure the attachment by rotating the button to the right

(Fig. 9). Before operating the unit, ensure that the rotary

handle is secure.

Removing and installing the cutting attachment

guard (depending on model)

If the unit is used for cutting undergrowth (with cutting blade),

remove the cutting attachment guard.

Remove the cutting attachment guard from the guard holder

by unscrewing the three (3) screws with a flat screwdriver

(Fig. 10). Keep parts for subsequent use.

If the unit is used as a lawn trimmer, install the guard

for the cutting attachment.

Install the cutting attachment guard in the guard holder

by screwing in the three (3) screws with a flat screwdriver.

Tighten the screws (Fig. 10).

Removing the cutting attachment and attaching

the cutting blade (depending on model)

Note: To facilitate removal or installation of the cutting blade

or the cutting attachment, place the unit on the ground

or a workbench.

Removing the cutting attachment

Note: First attach the guard to the cutting blade.

1. Align the shaft bush hole with the slot for the safety bar

and guide the safety bar into the shaft bush hole (Fig. 11).

2. Hold the safety bar in place by gripping it together

with the shaft of the unit (Fig. 12).

3. While holding the safety bar, remove the cutting

attachment by screwing it clockwise off the drive shaft

(Fig. 13). Keep the cutting attachment for subsequent

use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten GT-S 2-27 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

WOLF-Garten GT-S 2-27 Manual

Product: