638174

WOLF-Garten Expert 40 EA Manual

14
Zoom out
Zoom in
Previous page
1/110
Next page
14
G
Mulch
„Mulching“ is a process in which the grass is finely chopped by a
special cutting system and then deposited on the ground. The re-
sult is that the grass does not have to be collected and disposed
of. „Mulching“ also prevents the lawn from drying out.
3 Instructions for mulching
We recommend:
z Depending on the growth of grass, mulch 1 – 2 x per
week
z The grass should not be too high nor too wet!
z Go slow while mulching
z Take care that the blade channels do overlap.
z Do not cut grass more than 20 mm.
3 Note:
Mulching is not advisable in case of moss-affected or
entangled grass, because the cut material stays on the
moss surface and/or entanglement and thus cannot be
absorbed by the ground.
z Regularly scarify and manure the lawn.
Activating the mulch function
1 Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Do not start the motor until your feet are at a safe dis-
tance from the cutting tool.
1. Remove the grass collecting bag.
2. Set the switch to „MULCH“.
3. Start the motor.
Maintenance
General
1 Attention! Rotary cutter blade
Before all maintenance and cleaning work:
z pull out the power plug.
z Do not touch running blades.
Cleaning
z Clean mower thoroughly after each mowing with cloth or
brush.
z Clean the mulch flap at regular intervals with a small
broom .
z Do not spray with water.
Winter Storage
z Clean mower thoroughly before storing away.
z Have your mower thoroughly checked once a year by an ap-
proved Service Centre.
z Do not store it in a wet or humid place.
Changing blades
z For all works on blades, coupling and cutter bars, first of all,
pull out the power plug and wear protective gloves.
1 Attention!
An unbalance can develop after regrinding of the blade.
z Always regrind the blades in a specialist workshop,
because an unbalance check should be undertaken
according to the safety regulations.
EXPERT 34 E - EXPERT 37 E
z Always change blades in a specialist workshop. A torque
spanner of 10 mm is mandatorily required.
Fastening torque of the screws: 6 - 7 N-m .
EXPERT 40 E - EXPERT 40 EA
z Always change blades in a specialist workshop. A torque
spanner of 13 mm is mandatorily required.
Fastening torque of the screws: 16 - 18 N-m .
z Use only original WOLF-Garten spare parts.
Adjusting the Bowden cable coupling
1. Raise the drive bracket (1) app. 2 cm and hold.
2. Loosen the locking nut (2).
3. Turn the setscrew (3) left until the drive wheels are blocked
when you pull the mower backwards.
4. Tighten locking nut (2).
Spare parts
Q
T
U
U
U
V
Item number Order description Product information
4904 031 Grass catcher (34)
4907 031 Grass catcher (37)
4970 031 Grass catcher (40)
4904 096 Vi 34 FM Replacement blade 34 cm
4907 096 Vi 37 FM Replacement blade 37 cm
4970 096 Vi 40 FM Replacement blade 40 cm
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten Expert 40 EA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten Expert 40 EA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info