638019
12
Zoom out
Zoom in
Previous page
1/32
Next page
12
Maintenance
Cleaning work and blade change (g. W1)
First remove sparkplug connector and deactivate “QuickStart” (De-tension starter spring)
For cleaning work and blade change, tip the mower back as illustrated. Adjust the cutting height to the highest position and swing the
upper grip part towards the front (do not damage the Bowden cable, in the process).
Cleaning (g. W2)
First remove sparkplug connector and deactivate “QuickStart” (De-tension starter spring)
After each mowing, please clean the mower with a hand broom.
Never spay with water. Store the mower in a clean room.
Sharpen blade and replace (g. W3)
First remove sparkplug connector and deactivate “QuickStart” (De-tension starter spring)
Always have the blade sharpened by a specialist. Execute the blade change as illustrated.
Wear protective gloves for all work on the blade.
Note for the specialist workshop: Torque for the screw = 38-42 Nm, SW 17 mm.
Winter storage
First remove sparkplug connector and deactivate “QuickStart” (De-tension starter spring)
Drain fuel tank.
Drain carburettor
- therefore start engine, keep it runninug until it automaticalli switches off.
Clean the whole machine thoroughly
Change oil, 4-stroke engine.
Prepare engine for winter storage as follows:
- Remove spark plug
- Poor one spoon full of engine oil into spark plug hole
- Pull starter rope slowly to distribute oil evenly inside cylinder
- Replace spark plug but do not connect spark plug lead
- Pull starter rope until resistance is felt (valves are now closed)
Store mower in a cool and dry place.
We recommend: Have your mower thoroughly checked once a year by approved Service Agent.
Change oil only
First remove sparkplug connector and deactivate “QuickStart” (De-tension starter spring)
While engine is warm and fuel tank empty.
Change oil after the first 5 working hours. Thereafter chane engine oil every 25 working hours and at the end of the mowing season.
Change engine oil more frequently if working under extreme and dusty conditions. To drain the engine oil, remove oil filler cap, tilt
machine slowly to side and allow oil to drain from the crankcase through the filler.
Cleaning of Spark Plug
Check and clean regularly, reset plug gap as required (0,76 mm).
Cleaning of air filter
Refer to the engine manufacturer‘s handbook supplied.
Adjusting the clutch Bowden cable - Esprit 46 TMA (fig. W4/B7)
Lift the drive bar B7 (2) approx. 2 cm and hold. Loosen counternut W4 (A) and turn adjusting screw W4 (B) anticlockwise until the
drive wheels block when the mower is pulled backwards. Tighten counternut W4 (A) firmly.
Faults and how to remedy
Remedy (X) by:
Problem Possible cause
WOLF
service
workshop
Yourself
Motor does not start or
has no power:
QuickStart is not activated
Insufcient fuel in the tank
Spark plug lead not connected
Spark plug out of order
Air lter dirty or oily
Blade fastening screw loose
Clutch linings worn
---
---
---
---
---
X
X
X
X
X
X
X
---
---
Uneven cutting:
Cutting height misadjusted
Blunt blades
Air / duct catcher bag blocked
---
X
---
X
---
X
Drive does not start: Clutch Bowden cable misadjusted --- X
When in doubt, always consult a WOLF service workshop. Important: switch off the mower and disconnect the spark
plug lead before inspecting, cleaning or working on the blades.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten 2.46 TM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten 2.46 TM in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info