Manual WOLF-Garten 2.36 EK (page 10 of 32) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish)

638421

Zoom out

Zoom in

1/32

Assembly

Fixing of handle and adjustment of height (fig. M1/M2/M3/M4)

ATTENTION! Take care that the switch cable does not become caught and crushed when folding the handle frame. Fold upper

handle section forward. Tighten hand wheels firmly.

Fold complete handle backwards, position at the correct height and tighten firmly.

Folding of handle frame (fig. M5)

ATTENTION! Take care that the switch cable does not become caught and crushed when folding the handle frame.

Note! Unscrew the lower hand wheels (1) for about 2 cm/.1” either side, pull handle frame (2) either side, pull handle frame clear

of recesses until it can be folded forward easily.

Operation

Assembly of cable relief holder (fig. M6/M7)

Attaching of grassbox (fig. B1)

Lift deflector lid, locate grassbox hook into opening of chassis (see arrow) and replace lid.

Adjustment of cutting height (fig. B2)

Only when mower is stationary and rotating blade has come to complete standstill. Press button (a) and push chassis downwards

or pull upwards, as required. Release button at required cutting height (see indicator b).

Adjustment of cutting height to prepare for scarifying (fig. B2)

Press button (a), pushing chassis down byholding front grip (c) at the same time until grey area appears at the indicator (b).

Selection of Cutting height

If possible, mow when grass is dry in order to protect turf. Do not se cutting position too low when mowing very hight or wet grass.

We recommend an average cutting height of 4,0 cm.

Connecting to the mains (230 Volts, A.C., 50 Hz)

The mower operates from any normal household mains supply, provided with a 10 Amps. fuse.

Note: Use a residual current device (RCD) rated for a residual current not greater than 30 mA.

Starting (fig. B3/B4)

Switch on motor with mowerplaced on level and firm ground, not in high grass - alternatively tilt slightly.

Switch-on motor (fig. B4)

1. Depress button and hold (1).

2. Lift up bar and release button (2).

Switch-off motor (fig. B4)

Release bar (2).

Mowing (fig. B5)

Always let cable trail on the cut side of the lawn. Cable guidance: Place the cable firmly off the lawn or on the already cur

side of the lawn when starting to mow.

Emptying of Grassbox

The grassbox is full and should be emptied as soon as grass clippings remain uncollected on the ground behind your mower.

Note: Disconnect electricity by unplugging cable at the socket-before proceeding.

Cleaning (fig. W1)

Note: Disconnect electricity by unplugging cable at the socket before proceeding. Attention: Keep hands clear of moving blade.

Clean mower thoroughly after each mowing with cloth or brush. Do not spray with water. Keep mower in a dry room.

Change of cutter blade (fig. W2)

Note: always disconnect mains supply and wear protective gloves before undertaking any workat the cutter blades, cutter bar

and blade coupling. Change cutter blade using 10 mm spanner as illustraded. Torque wrench setting for screws 8-10 Nm. Take care

to carry out this work thoroughly. Use original spare parts only. Note: Sharpining of blades should be done by an approved service

centre as the correct balance of the blade after sharpening is very important and ought to be checked by an expert.

Winter Storage:

Clean mower thoroughly before storing away. Never spray mower with water and do not store it in a wet or humid place. Have

yourmower thoroughly checked once a yearby an approved Service Centre.

Maintenance

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten 2.36 EK in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

WOLF-Garten 2.36 EK Manual

Product: