78394
12
Zoom out
Zoom in
Previous page
1/94
Next page
12
G
Operation
Operating times
z Please check noise abatement regulations prevailing in your
country.
Feed cable through the strain relief
z Please feed cable through the strain relief .
Hang up collection bag
1 Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the re-
cesses (see arrow).
3. Replace the protective flap.
Set cut height
1 Attention! Rotary cutter blade
Undertake work/adjustments on the equipment only after
the motor is switched off and the cutting tool has come to a
standstill.
1. Pull the lever out.
2. Set the desired cutting height.
3. Press the lever back in.
Selection of Cutting height
z If possible, mow when grass is dry in order to protect turf. Do
not se cutting position too low when mowing very hight or wet
grass.
z We recommend an average cutting height of 40 mm.
Connecting to the mains (230 Volts, A.C., 50 Hz)
z The mower operates from any normal household mains sup-
ply, provided with a 16 Amps. fuse.
3 Note: Residual current protection device
These protection devices safeguard while touching
damaged wires, from insulation flaws and in certain cases,
also while damaging live wires.
z We recommend that the equipment only be plugged into
a power socket, which is protected by a residual current
protection device (RCD) with a residual current of not
more than 30 mA.
z Retrofit kits are available for old installations. Consult an
electrician.
Starting and Stoping
z Switch on motor with mowerplaced on level and firm ground.
z not in high grass - alternatively tilt slightly .
Switch-on motor
1. Depress button and hold (1).
2. Lift up bar (2).
3. Release bar (1).
Switch-off motor
z Release bar (2).
Emptying of Grassbox
The grassbox is full and should be emptied as soon as grass clip-
pings remain uncollected on the ground behind your mower.
1 Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Empty collection bag.
z Remove potential blockages in the cutting space before
starting.
Tips for mowing
z To prevent strips of grass from being left unmowed, the cutting
paths must always overlap a few centimeters .
Maintenance
General
1 Attention! Rotary cutter blade
Before all maintenance and cleaning work:
z pull out the power plug.
z Do not touch running blades.
Cleaning
z Clean mower thoroughly after each mowing with cloth or
brush.
z Do not spray with water.
Winter Storage
z Clean mower thoroughly before storing away.
z Have your mower thoroughly checked once a year by an ap-
proved Service Centre.
z Do not store it in a wet or humid place.
Changing blades
z For all works on blades, coupling and cutter bars, first of all,
pull out the power plug and wear protective gloves.
M
M
N
O
P
Q
Q
R
S
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten 2.34 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten 2.34 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info